manualshive.com logo in svg

Oracle X5-4, Service Manual

The Oracle X5-4 is a powerful and versatile server, designed for high-performance computing. To get acquainted with its features and functionalities, make sure to download the free "Getting Started Manual" from our website. This comprehensive manual will provide you with all the necessary information to maximize your experience with the Oracle X5-4.

Share
Download
background image

Replace the Fan Board (FRU)

Refer to the figure in step 4 to determine proper connections.

Note - 

Any excess cable length should be in the PCIe card area to allow better air flow through

the disk backplane area.

11.

Reinstall the P0 MR0/MR1 memory risers you removed earlier.

See 

“Install a Memory Riser Card” on page 152

.

12.

Prepare the server for operation.

See 

“Prepare the Server for Operation” on page 259

.

Replace the Fan Board (FRU)

This section provides instructions for replacing the fan board.

When servicing the components in this section, unplug the AC power cords and use ESD

protection.

Before You Begin

For serviceability considerations, see 

“Component Serviceability” on page 70

.

1.

Prepare the server for service.

See 

“Prepare the Server for Cold Service” on page 94

.

2.

Remove all fan modules.

See 

“Remove a Fan Module” on page 130

.

3.

Remove all memory risers.

See 

“Remove a Memory Riser Card” on page 145

.

Servicing FRU Components

221

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Related manuals for X5-4

IBM 5100 Installation Manual preview
5100
Brand: IBM Pages: 64
IBM x3800 - System - 8865 User Manual preview
x3800 - System - 8865
Brand: IBM Pages: 104
Rackable Systems S3116-NAS Getting Started Manual preview
S3116-NAS
Brand: Rackable Systems Pages: 4
Dot Hill AssuredSAN 4004 Series Fru Installation And Replacement Manual preview
AssuredSAN 4004 Series
Brand: Dot Hill Pages: 59
Olive Olive 2 User Manual preview
Olive 2
Brand: Olive Pages: 44
Olive Olive 4 HD Quick Start Manual preview
Olive 4 HD
Brand: Olive Pages: 19
ASROCK 2U4FH-12L User Manual preview
2U4FH-12L
Brand: ASROCK Pages: 40
Supermicro SuperServer 6029U-TR25M User Manual preview
SuperServer 6029U-TR25M
Brand: Supermicro Pages: 151
Infotrend EonServ 7000 Series Quick Installation Manual preview
EonServ 7000 Series
Brand: Infotrend Pages: 2
Fujitsu PRIMERGY TX1310 M1 Operating Manual preview
PRIMERGY TX1310 M1
Brand: Fujitsu Pages: 66
Fujitsu PRIMERGY T850 System Configurator And Order-Information Manual preview
PRIMERGY T850
Brand: Fujitsu Pages: 18
Fujitsu PRIMERGY TX1320 M1 Operating Manual preview
PRIMERGY TX1320 M1
Brand: Fujitsu Pages: 86
Fujitsu PRIMERGY TX120 S3 Operating Manual preview
PRIMERGY TX120 S3
Brand: Fujitsu Pages: 82
Fujitsu PRIMERGY TX1310 M3 Operating Manual preview
PRIMERGY TX1310 M3
Brand: Fujitsu Pages: 68
Fujitsu PRIMERGY TX1310 M1 Upgrade And Maintenance Manual preview
PRIMERGY TX1310 M1
Brand: Fujitsu Pages: 232
Fujitsu PRIMERGY TX120 S2 Operating Manual preview
PRIMERGY TX120 S2
Brand: Fujitsu Pages: 78
Fujitsu PRIMERGY TX1310 M5 Upgrade And Maintenance Manual preview
PRIMERGY TX1310 M5
Brand: Fujitsu Pages: 265
Fujitsu PRIMERGY TX1320 M1 Upgrade And Maintenance Manual preview
PRIMERGY TX1320 M1
Brand: Fujitsu Pages: 340

Brands by name

Popular brands

Load more brands