manualshive.com logo in svg

Oracle X5-4, Service Manual

The Oracle X5-4 is a powerful and versatile server, designed for high-performance computing. To get acquainted with its features and functionalities, make sure to download the free "Getting Started Manual" from our website. This comprehensive manual will provide you with all the necessary information to maximize your experience with the Oracle X5-4.

Share
Download
background image

Replace the Motherboard (FRU)

10.

To remove the SAS, NVMe (if present), and ESM cables from the system,

carefully thread each one between the CPU 0 heatsink and the power supply side

wall, and out towards the front of the system.

Some of the cable connectors only fit one way between the CPU 0 heat sink and power supply

side wall as the space is very narrow.

11.

Remove the data and power cables for the disk backplane.

See 

“Replace the Disk Drive Backplane (FRU)” on page 238

.

12.

Remove the power supply cable from the motherboard.

Connected to the motherboard from the power supply backplane.

13.

Remove any USB flash drives attached to the internal USB ports.

Make note of the ports for each USB flash drive.

14.

Remove the heatsinks and CPUs from the motherboard.

See 

“Remove a Heatsink and CPU (FRU)” on page 186

.

15.

Remove the system battery.

See 

“Replace the System Battery (CRU)” on page 172

.

16.

Loosen the green captive screw that secures the motherboard to the chassis.

Servicing FRU Components

251

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Related manuals for X5-4

Canon imagePRESS Server G200 Service Manual preview
imagePRESS Server G200
Brand: Canon Pages: 82
Canon P 400 Service Manual preview
P 400
Brand: Canon Pages: 88
H3C UniServer R4900 G5 Operating System Installation Manual preview
UniServer R4900 G5
Brand: H3C Pages: 141
Bang & Olufsen BeoMaster 5 Manual preview
BeoMaster 5
Brand: Bang & Olufsen Pages: 28
Intel SBXL52 - Server Compute Blade Hardware Maintenance Manual preview
SBXL52 - Server Compute Blade
Brand: Intel Pages: 126
Sun Microsystems Netra ft 1800 Installation Manual preview
Netra ft 1800
Brand: Sun Microsystems Pages: 90
TRENDnet TS-U100 - NAS Server - USB User Manual preview
TS-U100 - NAS Server - USB
Brand: TRENDnet Pages: 47
IBM totalstorage fastt100 Installation, User And Maintenance Manual preview
totalstorage fastt100
Brand: IBM Pages: 160
HP 376227-B21 - ProLiant InfiniBand 4x Fabric Copper Switch User Manual preview
376227-B21 - ProLiant InfiniBand 4x Fabric Copper Switch
Brand: HP Pages: 169
Fujitsu B23Q8WD-G-01-J Hardware Manual preview
B23Q8WD-G-01-J
Brand: Fujitsu Pages: 26
Fujitsu FUTRO S450 Operating Manual preview
FUTRO S450
Brand: Fujitsu Pages: 56
Fujitsu FD-1000ST User Manual preview
FD-1000ST
Brand: Fujitsu Pages: 36
Fujitsu FUTRO S550 Operating Manual preview
FUTRO S550
Brand: Fujitsu Pages: 61
Fujitsu BS2000 Operating Manual preview
BS2000
Brand: Fujitsu Pages: 30
Fujitsu ETERNUS DX Disk Configuration Manual preview
ETERNUS DX Disk
Brand: Fujitsu Pages: 85
Fujitsu BS2000/OSD Operation Manual preview
BS2000/OSD
Brand: Fujitsu Pages: 111
Fujitsu BX630 - PRIMERGY - S2 Dual Options Manual preview
BX630 - PRIMERGY - S2 Dual
Brand: Fujitsu Pages: 64
Fujitsu ESPRIMO A525-L Operating Manual preview
ESPRIMO A525-L
Brand: Fujitsu Pages: 68

Brands by name

Popular brands

Load more brands