manualshive.com logo in svg

Oracle X5-4, Service Manual

Share
Download
Oracle X5-4 Service Manual Download Page 65

Reset the SP Root Account Password or Recover the Root Account

Callout

Description

1

SP Reset

2

Host Warm Reset

3

NMI (Oracle Service use only)

Reset the SP Root Account Password or Recover

the Root Account

If necessary, system administrators can recover the Oracle ILOM root account (if accidentally

deleted) or reset the password for the Oracle ILOM root account to the factory default

password.

To perform either action, you need a local serial management port (SER MGT) connection

to Oracle ILOM. In addition, if the Physical Presence State is enabled (the default) in Oracle

ILOM, you must prove that you are physically present at the server as described in the

following procedure.

To recover the root account or root account password, perform these steps:

1.

Establish a local serial management connection to Oracle ILOM and log in to

Oracle ILOM using the default user account.

For example:

ORACLESP-000000000 login: 

default

Press and release the physical presence button

Troubleshooting and Diagnostics

65

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands