manualshive.com logo in svg

Oracle X5-4, Service Manual

Share
Download
Oracle X5-4 Service Manual Download Page 84

Locating a Failed Memory Riser Card, DIMM, or CPU

Callout

Description

1

Memory riser card Fault indicators

CPU Fault Indicators

The CPU Fault indicators are located on the motherboard between the memory riser cards

and the CPU. To see a lit CPU Fault indicator, look down from the top of the server and

sight through the memory riser cards and the support bracket near the CPU. The following

illustration shows the location of the CPU Fault indicators.

Note - 

When a CPU fails the fault indicators of its two memory riser cards also light, making it

easier to identify the failed CPU.

84

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands