manualshive.com logo in svg

Oracle X5-4, Service Manual

The Oracle X5-4 is a powerful and versatile server, designed for high-performance computing. To get acquainted with its features and functionalities, make sure to download the free "Getting Started Manual" from our website. This comprehensive manual will provide you with all the necessary information to maximize your experience with the Oracle X5-4.

Share
Download
background image

Troubleshooting Hardware Faults Using Oracle ILOM

Indicator Blink Rates

Note - 

The blink rate information described here might not apply to all server types (for

example, blade or rack mount).

This section describes the following indicator blink rates:

■

“Steady On” on page 46

■

“Steady Off” on page 47

■

“Slow Blink Rate” on page 47

■

“Fast Blink Rate” on page 48

■

“Single (Standby) Blink Rate” on page 48

■

“Slow Unison Blink Rate” on page 49

■

“Insertion Blink” on page 49

■

“Unison Steady On” on page 49

■

“Alternating (Invalid FRU) Blink Rate” on page 50

■

“Feedback Flash” on page 51

■

“Data Blink Rate” on page 51

■

“Sequential (Diagnostic) Blink Rate” on page 51

Steady On

For the steady on state, an indicator is continually on (lit) and does not blink. This indicates a

continuing condition, for example, an operational state (green) or a Service Action Required

fault state (amber).

46

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Related manuals for X5-4

IBM 5100 Installation Manual preview
5100
Brand: IBM Pages: 64
NEC NECCare Gold Express5800/320Fd Service Manual preview
NECCare Gold Express5800/320Fd
Brand: NEC Pages: 10
NEC SV8500 Setup Manual preview
SV8500
Brand: NEC Pages: 84
NEC NEC Express5800 Series Release Note preview
NEC Express5800 Series
Brand: NEC Pages: 6
LaCie 301160U - 1TB Ethernet Disk RAID Network Attached... Quick Install Manual preview
301160U - 1TB Ethernet Disk RAID Network Attached...
Brand: LaCie Pages: 5
IBM eserver xSeries 306 Option Installation Manual preview
eserver xSeries 306
Brand: IBM Pages: 46
IBM OpenPower 720 Technical Overview And Introduction preview
OpenPower 720
Brand: IBM Pages: 74
IBM 7945G2U Installation And User Manual preview
7945G2U
Brand: IBM Pages: 194
IBM 88632SU User Manual preview
88632SU
Brand: IBM Pages: 100
Compaq 244857-001 - TaskSmart - C4000 Model 60_duplicate Specification preview
244857-001 - TaskSmart - C4000 Model 60_duplicate
Brand: Compaq Pages: 9
LevelOne FPS-2013TXU User Manual preview
FPS-2013TXU
Brand: LevelOne Pages: 88
Supero SuperServer 6123L-8R User Manual preview
SuperServer 6123L-8R
Brand: Supero Pages: 105
Sun Microsystems Ultra Enterprise 3000 Installation Manual preview
Ultra Enterprise 3000
Brand: Sun Microsystems Pages: 48
Digi DIGI CONNECT ES Hardware Setup Manual preview
DIGI CONNECT ES
Brand: Digi Pages: 23
ABB doGATE Installation Instructions Manual preview
doGATE
Brand: ABB Pages: 9
ABB SPA OPC User Manual preview
SPA OPC
Brand: ABB Pages: 68
Thecus N3200PRO User Manual preview
N3200PRO
Brand: Thecus Pages: 102
USR IOT Cortex-M7 Series At Command Manual preview
Cortex-M7 Series
Brand: USR IOT Pages: 50

Brands by name

Popular brands

Load more brands