manualshive.com logo in svg

Oracle X5-4, Service Manual

Share
Download
Oracle X5-4 Service Manual Download Page 90

Locate a Failed Memory Riser Card, DIMM, or CPU

The following illustration shows a lit Fault indicator for memory riser card, P0/MR1. This

card contains the faulty DIMM. To locate the DIMM, remove the card and use the DIMM

Fault Remind circuit.

For more information, see 

“DIMM Fault Remind Circuit Components” on page 85

.

5.

Replace the failed component:

■

To replace a failed CPU, see 

“Replace a Faulty CPU (FRU)” on page 180

.

■

To replace a failed memory riser card or a DIMM, see 

“Replace a Faulty

Memory Riser Card” on page 144

.

Next Steps

■

“Replace a Faulty CPU (FRU)” on page 180

or

■

“Remove a Memory Riser Card” on page 145

or

■

“Replace a Faulty DIMM” on page 143

90

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands