Oracle X5-4 Service Manual Download Page 38 | Manualshive

Page: 38 / 358

background image

Troubleshooting Hardware Faults Using Oracle ILOM

Description

Section Links

Causes, actions, and preventative measures

for problems related to the cooling

subsystem.

“Troubleshooting System Cooling Issues” on page 52

Causes, actions, and preventative measures

for problems related to the power subsystem.

“Troubleshooting Power Issues” on page 54

Troubleshooting Hardware Faults Using Oracle

ILOM

This section provides a troubleshooting procedure that you can use to investigate server

hardware faults and, if necessary, prepare the server for service

When a server hardware fault event occurs the system lights the Service Action Required

indicator and captures the event in the system event log (SEL). If you have set up notification

through Oracle ILOM, you also receive an alert through the notification method you chose.

When you become aware of a hardware fault, you should address it immediately.

1.

Log in to the server SP Oracle ILOM web interface.

Open a browser and enter the IP address of the server SP. At the login screen, type a user name

(with administrator privileges) and password. The Summary screen appears.
The Status section of the Summary screen provides information about the server subsystems,

including:

■

Processors

■

Memory

■

Power

■

Cooling

■

Storage

■

Networking

■

I/O Modules

38

Oracle Server X5-4 Service Manual • December 2015

«
...
36
37
38
39
40
...
»

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Related manuals for X5-4

BladeCenter HS23

Brand: IBM Pages: 30

System x3950 X6

Brand: IBM Pages: 53

Express5800/180Ra-7

Brand: NEC Pages: 2

Express5800/120Rh-2

Brand: NEC Pages: 2

Express5800/120Rh-2

Brand: NEC Pages: 2

Express5800/120Rg-1

Brand: NEC Pages: 2

Express5800/120Rf-1

Brand: NEC Pages: 21

Express5800/120Ra-1

Brand: NEC Pages: 6

Express5800/120Mc2 series

Brand: NEC Pages: 2

EXPRESS5800/120Le

Brand: NEC Pages: 56

Express5800 320La

Brand: NEC Pages: 8

Express5800 120Li

Brand: NEC Pages: 2

Express5800 120Ed

Brand: NEC Pages: 29

Active Upgrade Express5800/320Fc

Brand: NEC Pages: 4

Brand: NEC Pages: 10

Express5800/120Rj-2

Brand: NEC Pages: 18

Express5800/120Rh-1

Brand: NEC Pages: 20

Bull NovaScale R620 Series

Brand: NEC Pages: 346

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands