manualshive.com logo in svg

Oracle X5-4, Service Manual

The Oracle X5-4 is a powerful and versatile server, designed for high-performance computing. To get acquainted with its features and functionalities, make sure to download the free "Getting Started Manual" from our website. This comprehensive manual will provide you with all the necessary information to maximize your experience with the Oracle X5-4.

Share
Download
background image

Component Serviceability, Locations, and Designations

Callout

Description

Callout

Description

1

PCIe 1

7

PCIe 7

2

PCIe 2

8

PCIe 8

3

PCIe 3

9

PCIe 9

4

PCIe 4

10

PCIe 10

5

PCIe 5

11

PCIe 11

6

PCIe 6

 

 

DVD, Storage Drive, and USB Designations

The DVD drive is located at the right lower front side of the front of the server.

The six storage drive slots are on the right side of the server and are designated consecutively

from bottom to top. The bottommost slot is designated as HDD-0, and the topmost slot is HDD-

5.

The two internal USB slots are located between the disk backplane board and the power supply

backplane board. An optional Oracle System Assistant flash drive is installed in the port marked

"OSA USB."

78

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Related manuals for X5-4

IBM BladeCenter HS23 User Manual preview
BladeCenter HS23
Brand: IBM Pages: 30
IBM System x3950 X6 Product Manual preview
System x3950 X6
Brand: IBM Pages: 53
IBM LS42 - BladeCenter - 7902 Service Manual preview
LS42 - BladeCenter - 7902
Brand: IBM Pages: 194
Lanner LEC-3010 User Manual preview
LEC-3010
Brand: Lanner Pages: 43
IBM xSeries 382 User Manual preview
xSeries 382
Brand: IBM Pages: 56
IBM System x3350 Type 4192 Installation Manual preview
System x3350 Type 4192
Brand: IBM Pages: 84
Vxl Itona E21S Specifications preview
Itona E21S
Brand: Vxl Pages: 2
Intel SRPM8 Quick Start Manual preview
SRPM8
Brand: Intel Pages: 32
Seyeon FW3150 User Manual preview
FW3150
Brand: Seyeon Pages: 10
TRENDnet TS-U100 - NAS Server - USB User Manual preview
TS-U100 - NAS Server - USB
Brand: TRENDnet Pages: 47
HPE ProLiant DL380 Gen9 Product End-Of-Life Disassembly Instructions preview
ProLiant DL380 Gen9
Brand: HPE Pages: 8
Extreme Networks ExtremeControl IA-A-305 Installation Manual preview
ExtremeControl IA-A-305
Brand: Extreme Networks Pages: 31
Extreme Networks EC8200A01-E6 Installation Manual preview
EC8200A01-E6
Brand: Extreme Networks Pages: 94
Allnet ALL69000 User Manual preview
ALL69000
Brand: Allnet Pages: 148
BITMAIN ANTMINER S19a Pro Installation Manual preview
ANTMINER S19a Pro
Brand: BITMAIN Pages: 17
Red Hat DIRECTORY SERVER 8.0 Installation Manual preview
DIRECTORY SERVER 8.0
Brand: Red Hat Pages: 128
Comtrol DeviceMaster LT User Manual preview
DeviceMaster LT
Brand: Comtrol Pages: 136
IBM 220 Service Manual preview
220
Brand: IBM Pages: 68

Brands by name

Popular brands

Load more brands