manualshive.com logo in svg

Oracle X5-4, Service Manual

The Oracle X5-4 is a powerful and versatile server, designed for high-performance computing. To get acquainted with its features and functionalities, make sure to download the free "Getting Started Manual" from our website. This comprehensive manual will provide you with all the necessary information to maximize your experience with the Oracle X5-4.

Share
Download
background image

Replace the Power Supply Backplane Board (FRU)

The power supply backplane cover is secured with a screw.

27.

Connect the data and power cables from the fan board to the motherboard.

28.

Connect the disk drive backplane power cable and ribbon data cable.

29.

To install the air divider:

Note - 

The air divider contains the Fault Remind button mechanism. To ensure that the

mechanism can engage the motherboard-mounted switch, the divider 

must

 be installed

correctly.

a.   

Gently rotate the air divider and cables from where you set it down in step 9

back to its proper position.

Ensure that all cables lay flat against the power supply side wall and do not cross over

each other. Do not allow the cables to interfere with the Fault Remind button mechanism

(button extension or light pipe).

Caution - 

Hardware damage. Try not to rub the cables against the CPU0 heatsink radiator fins.

They are sharp and can damage the cable insulation.

236

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Related manuals for X5-4

IBM BladeCenter HS23 Service Manual preview
BladeCenter HS23
Brand: IBM Pages: 36
NEC Univerge SV9300 Programming Manual preview
Univerge SV9300
Brand: NEC Pages: 47
NEC Univerge SV9100 Manual preview
Univerge SV9100
Brand: NEC Pages: 766
NEC Express5800/320Ma Software Installation And Configuration Manual preview
Express5800/320Ma
Brand: NEC Pages: 86
Panasonic KX-NS1000 Quick Reference Manual preview
KX-NS1000
Brand: Panasonic Pages: 28
Yamaha MCX-2000 - MusicCAST Digital Audio Server Owner'S Manual Addendum preview
MCX-2000 - MusicCAST Digital Audio Server
Brand: Yamaha Pages: 25
ImageTech printWiFi User Manual preview
printWiFi
Brand: ImageTech Pages: 44
TYAN GC68-B8036 Service Engineer'S Manual preview
GC68-B8036
Brand: TYAN Pages: 106
IBM 84894MU User Manual preview
84894MU
Brand: IBM Pages: 48
Western Digital Ultrastar Serv60+8 User Manual preview
Ultrastar Serv60+8
Brand: Western Digital Pages: 406
Stratus ftServer 2500 Site Planning Manual preview
ftServer 2500
Brand: Stratus Pages: 106
Supero SuperServer 5013G-M User Manual preview
SuperServer 5013G-M
Brand: Supero Pages: 104
Infrant Technologies ReadyNAS Duo User Manual preview
ReadyNAS Duo
Brand: Infrant Technologies Pages: 98
Fujitsu PRIMERGY TX1310 M1 Operating Manual preview
PRIMERGY TX1310 M1
Brand: Fujitsu Pages: 66
Fujitsu PRIMERGY T850 System Configurator And Order-Information Manual preview
PRIMERGY T850
Brand: Fujitsu Pages: 18
Fujitsu PRIMERGY TX1320 M1 Operating Manual preview
PRIMERGY TX1320 M1
Brand: Fujitsu Pages: 86
Fujitsu PRIMERGY TX120 S3 Operating Manual preview
PRIMERGY TX120 S3
Brand: Fujitsu Pages: 82
Fujitsu PRIMERGY TX1310 M3 Operating Manual preview
PRIMERGY TX1310 M3
Brand: Fujitsu Pages: 68

Brands by name

Popular brands

Load more brands