manualshive.com logo in svg

Oracle X5-4, Service Manual

Share
Download
Oracle X5-4 Service Manual Download Page 115

Remove a Storage Drive Filler Panel (CRU)

NVMe Storage Drive Virtual PCIe Slot Designation

If NVMe storage drives are installed, they are labeled on the system front panel as NVMe0,

NVMe1, NVMe2, and NVMe3. However, the server BIOS internally identifies these drives

by their virtual PCIe slot numbers. When using operating system commands to power NVMe

drives off before removal, you need to know the virtual PCIe slot number of the drive.

The following table lists the drive front panel label and its corresponding virtual PCIe slot

number used by the operating system.

Front Panel Storage Drive Label

Virtual PCIe Slot Number

NVMe0

PCIe slot 100

NVMe1

PCIe slot 101

NVMe2

PCIe slot 102

NVMe3

PCIe slot 103

Remove a Storage Drive Filler Panel (CRU)

For information about component filler panels, see 

“Component Filler Panels” on page 81

.

1.

Prepare the server for service.

See 

“Preparing to Service the Server” on page 93

.

2.

If necessary, press the Locator indicator button to deactivate the indicator.

3.

Identify the storage drive filler panel you want to remove.

4.

Push the release button to open the latch.

5.

To remove the filler panel, use the latch to pull the filler panel out of the slot.

Remove a Storage Drive (CRU)

Use this procedure to remove a storage drive from the server.

Before You Begin

■

For serviceability considerations, see 

“Component Serviceability” on page 70

.

Servicing CRU Components

115

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands