Oracle X5-4 Service Manual Download Page 107

Page: 107 / 358

Managing the Locator Indicator

To remove power from the server, disconnect the AC power cables from the

power supplies.

This action completely removes power from the server.

If you are performing a cold reset, wait at least 60 seconds before connecting the

AC power cables to the power supplies.

For information about cold resets, see

“Power Subsystem” on page 28

Managing the Locator Indicator

This section provides procedures for turning the Locator indicator on and off remotely using

Oracle ILOM, and locally using the front panel Locator button.

■

“Turn On the Locator Indicator Remotely (Oracle ILOM CLI)” on page 108

■

“Turn On the Locator Indicator Remotely (Oracle ILOM Web Interface)” on page 109

■

“Manage the Locator Indicator Locally” on page 110

Preparing to Service the Server

107

Summary of Contents for X5-4







































































































































































































































































































































































Search results

Summary of Contents for X5-4

Reviews:

Related manuals for X5-4

Brands by name

Popular brands

Oracle X5-4, Service Manual

Search results

Summary of Contents for X5-4

Reviews:

Related manuals for X5-4

Brands by name

Popular brands