Oracle X5-4 Service Manual Download Page 42

Page: 42 / 358

Troubleshooting Hardware Faults Using Oracle ILOM

Locator Indicator On

The Locator indicator helps identify a server in a rack of servers. It can be activated remotely

from Oracle ILOM or from the front panel (by pressing the Locator button). Once activated, the

indicator blinks at the fast blink rate.

For indicator blink rate information, see

“Indicator Blink Rates” on page 46

For information on remotely turning on the Locator indicator, see

“Managing the Locator

Indicator” on page 107

Over Temperature Condition

For a server in an over-temperature state, the amber Service Action Required and Temperature

indicators are on steady. The green OK indicator and the green SP indicator are on steady.

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Search results

Summary of Contents for X5-4

Reviews:

Brands by name

Popular brands

Oracle X5-4, Service Manual

Search results

Summary of Contents for X5-4

Reviews:

Brands by name

Popular brands