Oracle X5-4 Service Manual Download Page 131

Page: 131 / 358

Remove a Fan Module

Prepare the server:

■

For hot service, see

“Prepare the Server for Hot Service” on page 93

■

For cold service, see

“Prepare the Server for Cold Service” on page 94

If necessary, slide the server partially out from the rack.

At the back of the server, verify that the cables have sufficient length and

clearance to extend the server.

The cable management arm (CMA) that is supplied with the server is hinged to facilitate

extending the server to the maintenance position. However, ensure that the cables do not

impede the sliding movement and are not damaged or overextended by it.

At the front of the server, release the slide rails by pushing the two green

latches inward.

Identify the faulty fan module using the fan module indicators.

Servicing CRU Components

131

Summary of Contents for X5-4







































































































































































































































































































































































Search results

Summary of Contents for X5-4

Reviews:

Related manuals for X5-4

Brands by name

Popular brands

Oracle X5-4, Service Manual

Search results

Summary of Contents for X5-4

Reviews:

Related manuals for X5-4

Brands by name

Popular brands