manualshive.com logo in svg

Oracle X5-4, Service Manual

Share
Download
Oracle X5-4 Service Manual Download Page 164

Install a PCIe Card

-or-

■

“Prepare the Server for Operation” on page 259

Install a PCIe Card

When servicing the components in this section, unplug the AC power cords and use ESD

protection.

For PCIe card support and installation order information, refer to 

“PCIe Slot

Reference” on page 167

 and the 

Product Notes

 for the server.

This procedure describes how to install a PCIe card.

Caution - 

Component damage. Ensure that all power is removed from the server before

removing or installing PCIe cards. You must disconnect the power cables before performing

this procedure.

Before You Begin

■

For serviceability considerations, see 

“Component Serviceability” on page 70

.

■

For PCIe slot designation information, see 

“Component Designations” on page 73

.

1.

Unpack the PCIe card and place it on an antistatic mat.

2.

Prepare the server for service.

See 

“Prepare the Server for Cold Service” on page 94

.

164

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands