manualshive.com logo in svg

Oracle X5-4, Service Manual

Share
Download
Oracle X5-4 Service Manual Download Page 60

Attach Devices to the Server

3.

To access the Oracle ILOM command-line interface (CLI) locally using the

management port, connect a serial null modem cable to the RJ-45 serial port

labeled SER MGT.

See 

“Back Panel Connector Locations” on page 60

.

4.

To interact with the system console locally, connect a monitor [1], keyboard [2]

and mouse [3] to the server front panel connectors as shown in the illustration

below.

Back Panel Connector Locations

The following illustration shows and describes the locations of the back panel connectors. Use

this information to set up the server, so you can access diagnostic tools and manage the server

during service.

60

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands