Oracle X5-4 Service Manual Download Page 247

Page: 247 / 358

Replace the Motherboard (FRU)

To engage the two connectors, gently push the card downward at the two green

pressure points on the edges of the card.

Connect the SP card cable to the connector on the SP Card.

To secure the card, tighten the green captive screw.

Prepare the server for operation.

See

“Prepare the Server for Operation” on page 259

Replace the Motherboard (FRU)

This section provides instructions for replacing the server motherboard.

When servicing the components in this section, unplug the AC power cords and use ESD

protection.

Servicing FRU Components

247

Summary of Contents for X5-4







































































































































































































































































































































































Search results

Summary of Contents for X5-4

Reviews:

Related manuals for X5-4

Brands by name

Popular brands

Oracle X5-4, Service Manual

Search results

Summary of Contents for X5-4

Reviews:

Related manuals for X5-4

Brands by name

Popular brands