Oracle X5-4 Service Manual Download Page 138

Page: 138 / 358

Install a Power Supply

To unlock the power supply handle, squeeze the release latch.

To disengage the power supply, rotate the release latch fully downward.

This action disengages the power supply from the internal power supply backplane connector.

To remove the power supply, use the latch to slide it partially out of the chassis

until you can support it with your free hand and remove it completely.

Next Steps

“Install a Power Supply” on page 138

Install a Power Supply

This procedure describes how to install a power supply (PSU). When installing a PSU, ensure

that the pawl near the hinge of the latch engages the slot in the sidewall of the PSU bay. The

pawl supplies the necessary leverage to seat the PSU connector with the PSU backplane.

138

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Search results

Summary of Contents for X5-4

Reviews:

Brands by name

Popular brands

Oracle X5-4, Service Manual

Search results

Summary of Contents for X5-4

Reviews:

Brands by name

Popular brands