manualshive.com logo in svg

Oracle X5-4, Service Manual

Share
Download
Oracle X5-4 Service Manual Download Page 34

Server Subsystems Overview

System Management Subsystem

The server has two embedded system management tools (Oracle ILOM and Oracle System

Assistant) and a suite of command line tools that can be run from the host.

Service Processor (SP) Oracle ILOM

The server comes with a removable service processor (SP) daughter card that is mounted on

the server motherboard. The SP supports the industry-standard IPMI feature set and includes

Oracle Integrated Lights Out Manager (ILOM) 3.2.5 and remote redirection of keyboard, video,

mouse, and storage (KVMS).

The SP runs Oracle ILOM, a single-server management tool that allows you to monitor

and maintain your server by providing real-time status and detailed information about the

subsystems and components in your server. Oracle ILOM runs independently of the server

OS and is accessible in both full power and standby power modes. The SP Oracle ILOM is

accessible through the SP 100/1000/10000 Ethernet NET MGT port located on the server

back panel or through one of the host's four built-in 10 GigabitEthernet ports (using sideband

management).

Oracle System Assistant

Your server might also come equipped with Oracle System Assistant. Oracle System Assistant

is a server provisioning and update tool that assists in initial server set up and OS installation

and allows you to easily manage server updates. As an option, Oracle System Assistant is

delivered on a USB flash drive that is factory-installed in the internal USB slot labeled "OSA

USB." The drive is configured with a server-specific version of Oracle System Assistant. You

can start Oracle System Assistant from the server boot screen or from Oracle ILOM.

34

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands