Oracle X5-4 Service Manual Download Page 174

Page: 174 / 358

Replace the System Battery (CRU)

The battery is located toward the back of the server between PCIe slot 1 and the power supply

side wall.

Callout

Description

System battery

If necessary, remove the PCIe card in slot 1.

You might need to remove the card to access the battery. See

“Remove a PCIe

Card” on page 161

Remove the battery from the battery holder by pushing the back of the battery

(negative side) toward the metal tab (on the positive side) and lifting the battery

up and out of the battery holder.

Take care not to deform the tab when pushing against it.

174

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Search results

Summary of Contents for X5-4

Reviews:

Related manuals for X5-4

Brands by name

Popular brands

Oracle X5-4, Service Manual

Search results

Summary of Contents for X5-4

Reviews:

Related manuals for X5-4

Brands by name

Popular brands