manualshive.com logo in svg

Oracle X5-4, Service Manual

Share
Download
Oracle X5-4 Service Manual Download Page 120

Install a Storage Drive Filler Panel (CRU)

Callout

Description

1

OK to Remove indicator

2

Service Action Required indicator

3

OK/Activity indicator

The functions of the drive status indicators are described below.

For indicator blink rate information, see 

“Indicator Blink Rates” on page 46

.

OK to Remove Indicator

Blue indicator. Indicates that the storage drive can be removed safely during a hot-service

operation.

Service Action Required Indicator

Amber indicator. Indicates that the storage drive is faulty. The front and back panel Service

Action Required indicators are also lit if the system detects a storage drive fault.

120

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands