manualshive.com logo in svg

Oracle X5-4, Service Manual

Share
Download
Oracle X5-4 Service Manual Download Page 262

(Optional) Install the Server Into the Rack

13.

Secure the power cords with the power cord retaining clips.

14.

Connect any other cables to their connectors or ports on the back of the server.

If the cable management arm (CMA) is in the way, disconnect the left CMA release and swing

the CMA open.

15.

If necessary, reconnect the CMA.

See 

“(Optional) Install Cable Management Arm” on page 266

.

Swing the CMA closed and latch it to the left rack rail.

16.

Power on the server.

See 

“Power On the Server” on page 271

.

(Optional) Install the Server Into the Rack

Before You Begin

When preparing the server for operation, use these optional steps to install the server in the

rack.

Caution - 

Physical or component damage. The server is heavy and cannot be safely installed in

the rack by a single person. Use multiple personnel and a mechanical lift to install the server in

the rack.

262

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands