manualshive.com logo in svg

Oracle X5-4, Service Manual

Share
Download
Oracle X5-4 Service Manual Download Page 274

About the BIOS Setup Utility

■

“UEFI Mode BIOS Setup Utility Screens” on page 333

Legacy Mode BIOS Setup Utility Screens

This section contains screen captures of legacy mode BIOS Setup Utility screens. To access the

BIOS Setup Utility, see 

“Access the BIOS Setup Utility” on page 338

.

BIOS Menu Top-Level

The following table provides descriptions for the Legacy mode top-level BIOS setup menus.

Menu

Description

Main

General system and product information, including date and time, security, hardware

configuration and CPU, and DIMM information.

Advanced

Configuration information for processors, CPU power management, USB ports, serial ports,

trusted computing, network stack, legacy iSCSI, BMC network configuration, and UEFI

iSCSI configuration.

IO

Configuration interface for plug-and-play (PnP) devices, virtualization, internal devices,and

add-in cards.

Boot

Configuration interface for boot settings, including boot mode (Legacy, UEFI), Oracle

System Assistant Configuration, and boot option priority.

Exit

Save or discard changes.

The following illustration identifies the sub-menus that you can access from each of the top-

level BIOS menus.

Main Screen (Legacy)

Note - 

To facilitate search, a list of keywords appears after each screen capture.

274

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands