Oracle X5-4 Service Manual Download Page 207

Page: 207 / 358

Replace the SAS 12 Gb/s Internal HBA SAS Cables (FRU)

There are three clips. The HBA cables are attached to the bottom clip.

Once the HBA cable is clear of the air divider clips, gently pry the air divider

cable shield [A in the figure above] away from the power supply just enough

to allow you to slide out the HBA cables.

The HBA cables need to be completely free of the air divider.

Carefully thread the ends of HBA cables you detached from the HBA through the

narrow space between the P0 heat sink and the power supply cage and up and

out of the system.

The space between the P0 heat sink and the power supply cage is narrow;.the SAS cable

connectors will only fit through one way.

Servicing FRU Components

207

Summary of Contents for X5-4







































































































































































































































































































































































Search results

Summary of Contents for X5-4

Reviews:

Related manuals for X5-4

Brands by name

Popular brands

Oracle X5-4, Service Manual

Search results

Summary of Contents for X5-4

Reviews:

Related manuals for X5-4

Brands by name

Popular brands