manualshive.com logo in svg

Oracle X5-4, Service Manual

Share
Download
Oracle X5-4 Service Manual Download Page 74

Component Serviceability, Locations, and Designations

Callout

Description

Callout

Description

1

Fan Module, FM 0

4

Fan Module, FM 3

2

Fan Module, FM 1

5

Fan Module, FM 4

3

Fan Module, FM 2

6

Fan Module, FM 5

CPUs and Memory Riser Card Slots Designations

The four CPU sockets are located in the middle of the server and are designated consecutively

from right to left (from the front of the server). The rightmost socket is CPU-0 and is designated

as P0, and the leftmost socket is CPU-3, designated as P3.

The eight memory riser (MR) card slots are located between the fan module slots and the CPU

sockets. Consecutively from right to left, the rightmost slot is slot 0, and the leftmost slot is slot

7.

The slots are also designated by their association with the four CPU sockets (P0-P3). Two slots

are assigned to each CPU socket. For example, slots 0 and 1 are paired with CPU socket, P0,

and are designated as P0/MR0 and P0/MR1. Slots 2 and 3 are paired with CPU socket, P1 and

are designated as P1/MR0 and P1/MR1. This numbering pattern continues for the remaining

slots.

74

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands