manualshive.com logo in svg

Oracle X5-4, Service Manual

The Oracle X5-4 is a powerful and versatile server, designed for high-performance computing. To get acquainted with its features and functionalities, make sure to download the free "Getting Started Manual" from our website. This comprehensive manual will provide you with all the necessary information to maximize your experience with the Oracle X5-4.

Share
Download
background image

Prepare the Server for Cold Service

2.

Remove the power cord retainer clips by lifting them up to disengage them from

the power cords.

3.

Remove both server power cords.

Caution - 

Data loss. Removing the power cords when the server is in full power mode results

in an immediate shut down of the server. Do not remove the power cords if the server is in full

power mode.

4.

To slide the server out of the rack to the maintenance position, do the following:

Most component service procedures can be performed without removing the server entirely

from the rack. Instead, the server can be slid out of the rack on its support rails to an extended

and locked position called the maintenance position.

a.   

At the back of the server, verify that the cables have sufficient length

and clearance to extend the server to the maintenance position without

damaging or overextending the cables.

The cable management arm (CMA) that is supplied with the server is hinged to facilitate

extending the server to the maintenance position. Ensure the sliding movement does not

impede or damage the cables. If necessary, label and remove cables from the back of the

server.

96

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Related manuals for X5-4

NEC HX4500 Configuration Manual preview
HX4500
Brand: NEC Pages: 74
NEC Express5800/T120e Quick Start Manual preview
Express5800/T120e
Brand: NEC Pages: 6
NEC Express5800/T120e Getting Started preview
Express5800/T120e
Brand: NEC Pages: 2
NEC Express5800/T110i Getting Started preview
Express5800/T110i
Brand: NEC Pages: 2
NEC EXPRESS5800/R320d-E4 Configuration Manual preview
EXPRESS5800/R320d-E4
Brand: NEC Pages: 19
NEC Express5800/R320d-M4 Series User Manual preview
Express5800/R320d-M4 Series
Brand: NEC Pages: 98
NEC Express5800/R120h-2M Getting Started preview
Express5800/R120h-2M
Brand: NEC Pages: 2
NEC Express5800/R120f-1E Use Precautions preview
Express5800/R120f-1E
Brand: NEC Pages: 12
NEC Express5800/R120d-1E Hardware Specification preview
Express5800/R120d-1E
Brand: NEC Pages: 2
NEC Express5800/R110i-1 Getting Started preview
Express5800/R110i-1
Brand: NEC Pages: 2
NEC Express5800/R110h-1 System Configuration Manual preview
Express5800/R110h-1
Brand: NEC Pages: 40
NEC Express5800/A2040d Configuration Manual preview
Express5800/A2040d
Brand: NEC Pages: 83
NEC Express5800/320Lc Datasheet preview
Express5800/320Lc
Brand: NEC Pages: 4
NEC Express5800/120Rj-2 Datasheet preview
Express5800/120Rj-2
Brand: NEC Pages: 2
NEC NEAX2000 IVS2 Manual preview
NEAX2000 IVS2
Brand: NEC Pages: 106
NEC Express5800/T120d User Manual preview
Express5800/T120d
Brand: NEC Pages: 153
NEC Express5800/T110g-S User Manual preview
Express5800/T110g-S
Brand: NEC Pages: 128
NEC Express5800/R120g-1E Maintenance Manual preview
Express5800/R120g-1E
Brand: NEC Pages: 224

Brands by name

Popular brands

Load more brands