Oracle X5-4 Service Manual Download Page 108

Page: 108 / 358

Turn On the Locator Indicator Remotely (Oracle ILOM CLI)

Turn On the Locator Indicator Remotely (Oracle

ILOM CLI)

The Locator indicator helps you identify the a specific server in a rack.

Open an SSH session and at the command line log in to the Oracle ILOM CLI.

ssh root@

ipadress

where

ipadress

is the IP address of the server SP.

For more information, refer to the

Oracle X5 Series Servers Administration Guide

http://

www.oracle.com/goto/x86AdminDiag/docs

The Oracle ILOM CLI prompt appears:

turn on

the Locator indicator, type the following command at the prompt:

set /System/ locator_indicator=on

Note -

turn off

the Locator indicator, type:

set /System/ locator_indicator=off

To verify the status of the Locator indicator, type:

–>

show /System/ locator_indicator

The output of the command appears:

/System

Properties:

locator_indicator = Off

The value

locator_indicator

shows the status as either

Off

See Also

■

Oracle Integrated Lights Out Manager 3.2.x Documentation Library at:

http://www.

oracle.com/goto/ILOM/docs

108

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Search results

Summary of Contents for X5-4

Reviews:

Brands by name

Popular brands

Oracle X5-4, Service Manual

Search results

Summary of Contents for X5-4

Reviews:

Brands by name

Popular brands