![background image](http://html1.mh-extra.com/html/omron/cx-process-monitor-plus-2/cx-process-monitor-plus-2_operation-manual_744195035.webp)
20
CX-Process Monitor Plus
Section 1-1
1-1-7
CX-Process Monitor Plus Setting and Monitoring Capabilities
The data that can be set and monitored using the CX-Process Monitor Plus is
listed in the following table.
The following items must be set in advance using the CX-Process Tool.
Note
Using CX-Process Monitor Plus, you can monitor and set only the data given
above to which tag names have been allocated. Also, be sure to use CX-Pro-
cess Tool to make tag name settings.
Item
Loop Control Unit
Loop Control Board
Function block data
Control Blocks:
Basic PID (Block Model 011), Advanced PID (Block Model
012), Blended PID (Block Model 013), Batch Flowrate Capture
(Block Model 014), Indication and Setting (Block Model 031),
Indication and Operation (Block Model 032), Ratio Setting
(Block Model 033), Indicator (Block Model 034), 2-position
ON/OFF (Block Model 001), and 3-position ON/OFF (Block
Model 002)
Operation Blocks:
High/Low Alarm (Block Model 111), Segment Program 2
(Block Model 157), ON/OFF Valve Manipulator (Block Model
221), Motor Manipulator (Block Model 222), Reversible Motor
Manipulator (Block Model 223), Motor Opening Manipulator
(Block Model 224), Timer (Block Model 205) and Counter
(Block Model 208)
Contact signals
Contact signals through Contact Distributor (Block Model 201)
+ Internal Switch (Block Model 209)
Analog
signals
Sent to
Monitor Plus
Analog signals through Input Selector (Block Model 162)
Set from
Monitor Plus
Analog signals through Constant Generator (Block Model 166)
Item
Loop Control Unit
Loop Control Board
1. Register the function
blocks used for data
exchange.
Function block data
exchange
Receive All Blocks (Block Model
461) and Send All Blocks (Block
Model 462)
HMI functions in the System
Common block (Block Model
000)
Contact signal data
exchange
Contact Distributor block (Block Model 201) + Internal Switch block
(Block Model 209)
Analog signal data
exchange
Input Selector block (Block Model 162) and Constant Generator
block (Block Model 166)
2. Set the tag names.
Function Block Data:
CSV tags are set in the CX-Process Tool by selecting the function
blocks and then selected
Settings – Tag Setting – CSV Tags.
Contact Signals:
tags for Monitor Plus are set for each contact in the Internal Switch
blocks. The function blocks are then selected, the right mouse button
clicked, and
Tag Setting – Monitor Plus Tag
is selected.
Analog Signals:
tags for Monitor Plus are set for each analog signal in the Variable
ITEM Setting and Constant Generator blocks. The function blocks
are then selected, the right mouse button clicked, and
Tag Setting –
Monitor Plus Tag
is selected.
3. Create the monitor tag file.
Start the CX-Monitor Plus and click the
Run
or
Setup
Button.
Summary of Contents for CX-Process Monitor Plus 2
