Mitsubishi Electric MR-J4W2 Instruction Manual Download Page 282 | Manualshive

Page: 282 / 542

background image

13. USING STO FUNCTION

13 - 1

13. USING STO FUNCTION

POINT

In the case of STO function of this servo amplifier, energies to servo motor are
interrupted in all axes at the same time.
In the torque control mode, the forced stop deceleration function is not available.
The MR-J4W2-0303B6 servo amplifier is not compatible with the STO function.

13.1 Introduction

This section provides the cautions of the STO function.

13.1.1 Summary

This servo amplifier complies with the following safety standards.

ISO/EN ISO 13849-1 category 3 PL d
IEC 61508 SIL 2
IEC/EN 61800-5-2 SIL 2

13.1.2 Terms related to safety

The STO function shuts down energy to servo motors, thus removing torque. This function electronically cuts
off power supply in the servo amplifier.
The purpose of this function is as follows.

(1) Uncontrolled stop according to stop category 0 of IEC/EN 60204-1

(2) Preventing unexpected start-up

13.1.3 Cautions

The following basic safety notes must be read carefully and fully in order to prevent injury to persons or
damage to property.
Only qualified personnel are authorized to install, start-up, repair, or service the machines in which these
components are installed.
They must be familiar with all applicable local regulations and laws in which machines with these
components are installed, particularly the standards mentioned in this manual.
The staff responsible for this work must be given express permission from the company to perform start-up,
programming, configuration, and maintenance of the machine in accordance with the safety standards.

WARNING

Improper installation of the safety related components or systems may cause
improper operation in which safety is not assured, and may result in severe
injuries or even death.

Protective Measures

This servo amplifier satisfies the Safe Torque Off (STO) function described in IEC/EN 61800-5-2 by
preventing the energy supply from the servo amplifier to the servo motor. If an external force acts upon
the drive axis, additional safety measures, such as brakes or counterbalances must be used.

«
...
280
281
282
283
284
...
»

Summary of Contents for MR-J4W2































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2

Brand: Octave Pages: 23

Brand: NAD Pages: 2

Brand: Calypso Pages: 17

Brand: W Audio Pages: 20

Brand: Samson Pages: 56

Brand: Texas Instruments Pages: 8

Brand: Velleman-Kit Pages: 24

maestro Rr ADS-MRR

Brand: iDataLink Pages: 37

Brand: Lab.gruppen Pages: 18

Brand: Pyle Pro Pages: 6

Brand: stellar labs Pages: 7

Brand: Mark Levinson Pages: 8

Brand: JET CITY AMPLIFICATION Pages: 18

Bassman Bassman 100

Brand: Fender Pages: 16

Brand: Marantz Pages: 86

1812R Blues King 12

Brand: SUPRO Pages: 8

Brand: TX Digicast Pages: 19

Brand: Toa Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands