Mitel Inter-Tel Axxess Administrator'S Manual Download Page 376

Page: 376 / 384

Page 360

Index

Inter-Tel

Axxess

Administrator Guide — Issue 11.0, May 2008

Internet Protocol (IP)

devices   100
local loop support   168
MGCP   103

Internet Protocol Card (IPC)   77
Internet Protocol Resource Card (IPRC)   77
Internet Protocol Resource Card (IPRC) Daughter Enhanced (DE)   77
Internet Protocol Resource Card 16 Port Daughter Enhanced   77
Inter-Station Messages   194

alternate message source 198
answering 197
canceling message you sent 196
canceling waiting message   198
indications   194
mailboxes   194
silent   195
viewing   196

Inter-Tel AIM Endpoint   95
Inter-Tel Endpoint Displays   154
Inter-Tel Endpoint Features   172
Inter-Tel Endpoints   77
Inter-Tel Protocol (ITP) and SIP Operating Modes   104
Introduction   2, 75,   291

hardware 75

IP (Internet Protocol)

devices 100

IP and SIP Devices 100

endpoints   101
IP SLA   101
peer-to-peer (P2P)   104
softphone   102

IP and SIP Endpoint Identification   101
IP and SIP Feature Exceptions   107
IP Device Installation and Configuration   101
IP Devices and Local Loop Support   168
IP Limitations   101
IP SoftPhone   102
ITP and SIP Supported Features   105

Japanese Prompts and Displays 15

alphanumeric   17
date and time   14
Do-Not-Disturb   266
multilingual capability   180
reminder messages   275
system speed dialing   244

Keymaps 83
Keymaps, Switching 177

Lamp Option Card (LOC) 97
Language 15

alphanumeric   17
date and time 14
Do-Not-Disturb   266
Inter-Tel endpoints   275
multilingual capability   180
system speed dialing   244

Language Selection   180
Last Number Dialed/Saved   260
LCD Contrast Adjustment   82
LCD Touch Screen   102
Leaving Messages   195
Light-Emitting Diode (LED) Indications   88
Light-Emitting Diodes (LEDs)

DSS/BLF keys   100
endpoint   88
indicators   75
red/green 90

Linear Hunt Group   132
Liquid Crystal Display (LCD)   80,   81
Listening to the Next/Previous Name 302
Locating a Name   301
Longest Idle Search   143

Mailbox

directory 304
private 304
unlisted number 304

Mailbox and Extension ID Personal Options   54
Mailbox Numbers   304
Mailboxes   315

associated/non-associated   317
dial-0 destination 316
directory   54,   300
directory names   300
envelope settings   54
message indications   194
message notification station   317
operator destination 316
passwords 54,   3 15
personal greeting   54
receive only 315
remote messaging   315
standard   315
subscriber access   320
system administrator 54,   3 15

Maintaining Mailboxes and Group Lists   54
Maintenance of Node-Spanning Hunt Groups   151
Major Alarm   44
Major Alarms   42,   2 81
Managing System and Network Alarms   42
Manual Call Forwarding and System Forwarding   235
Manual Forwarding to Public Network   241
Media Gateway Control Protocol (MGCP)   103
Members   144
Message Center   194

forwarding to 241
hunt group as 134

Message Envelope Contents 54
Message Lamp 116

Summary of Contents for Inter-Tel Axxess

































































































































































































































































































































































































Search results

Summary of Contents for Inter-Tel Axxess

Reviews:

Mitel Inter-Tel Axxess, Administrator'S Manual, Page: 376 / 384

Search results

Summary of Contents for Inter-Tel Axxess

Reviews: