manualshive.com logo in svg

Mitel Inter-Tel Axxess, Administrator'S Manual, Page: 60 / 384

Share
Download
Mitel Inter-Tel Axxess Administrator'S Manual Download Page 60

Page  44

Administrator Procedures

Inter-Tel

® 

Axxess

® 

Administrator Guide — Issue 11.0, May 2008

Network Alarms

To respond to a major alarm from any alarm display station, take the appropriate action as indi-
cated in the following table.

A major alarm message, MAJOR ALARM, appears on all display endpoints in the event of a
system-wide failure. If the major alarm appears on a group of endpoints, the associated Keyset
Card may have failed. The warning might also appear on a single endpoint if the endpoint or
its cabling may be defective. Because they indicate that all or part of the system is inoperative,
major alarms require immediate attention from service personnel.

 SYS ALARM #21 
V-MAIL 80% FULL

The Voice Mail disk space is 80% of full. If it reaches 100%, Voice Mail cannot 
accept any messages until disk space is made available.

Contact service personnel.

 SYS ALARM #22 
V-MAIL 100% FULL

100% of the Voice Mail disk space is in use. Voice mail cannot accept any mes-
sages until disk space is made available.

Contact service personnel.

 SYS ALARM #23
SMDR 80% FULL

The SMDR disk space is 80% of full. If it reaches 100% before the SMDR infor-
mation is cleared, no further SMDR recording will be possible.

Contact service personnel.

 SYS ALARM #24
SMDR 100% FULL

100% of the (Station Message Detail Recording) SMDR disk space is in use. No 
further SMDR recording is possible.

Contact service personnel.

 SYS ALARM #32 
INSUF BAND

The IP Network does not have enough bandwidth to support the IP call that is 
currently connected to the extension. If this alarm is generated frequently, it could 
indicate a network problem that requires the attention of your network administra-
tor. 

Notify your network administrator. Make sure the affected device is not behind a 
firewall or NAT.

Table 7. 

Alarms and Suggested Responses (Continued)

ALARM DISPLAY

DESCRIPTION AND ACTION REQUIRED 

Table 8. 

Alarm Types and Suggested Responses

ALARM TEXT

DESCRIPTION AND ACTION REQUIRED 

#100-199
#200-224

SYS ALARM #XXX

CALL TECHNICIAN

These alarms indicate that an equipment failure has occurred that 
requires the attention of service personnel. 

Contact service personnel. (Be prepared to provide them with all 
alarm information, as well as what was taking place when the alarm 
occurred.)

Summary of Contents for Inter-Tel Axxess

































































































































































































































































































































































































Reviews:

No comments