Mitel Inter-Tel Axxess Administrator'S Manual Download Page 371

Page: 371 / 384

Page 355

Index

Inter-Tel

Axxess

Administrator Guide — Issue 11.0,

May 2008

Index

Symbols

“All Transient Displays” Station Flag   174
“DKTS Alternate Transient Display Timer” Station Flag And Timer
175
“DKTS Alternate Transient Display Timer” Station Flag and Timer
175
“Hot” DIALPAD Buttons vs. “SPCL Key Required For Feature Code
Entry” Flag   116
“Hot” Dialpad Buttons vs. “SPCL Key Required For Feature Code En-
try” Flag   116
“Send Alert Burst To Headset” Station Flag   91
“Transient Call Indication On Call Answer” Station Flag   175
8-Line Dual Circuits 95
8-Line IMX AIM Analog Endpoints On Dual Circuits   95
8-Line IMX AIM Analog Endpoints on Dual Circuits 95

Absorbed Digits   161
Accept Key   83
Accepting a Name   302
Access to the Features   116
Account Codes 207

all calls following   210
forced   207
on outside calls   202
standard   207

ACD Agent ID Automatic Connect Flag   147
ACD Agent IDs   144
ACD Agent IDs Automatic Connect Flag   147
ACD Agent Login/Logout   145
ACD Agent Wrap-Up Timer 147
ACD Call Distribution   143
ACD Hunt Groups   143

agent wrap-up   147
agents   145,   146
balanced count 143
call circulation   143
login/logout   145, 146
longest idle   143
using extension lists   144
wrap-up timer   147

ACD Hunt Groups Span Nodes   149
Add Parties to a Conference   224
Adjusting LCD Contrast   82
Administrator

feature codes   124, 354
freeze/unfreeze   51
network alarms   42
night mode   13
programming   18
setting time and date   14,   15

speed-dial programming   38
system alarms   42
system database programming   16,   18

Administrator Duties   12
Administrator Feature Codes   124
Administrator Procedures   11
Administrator Programming Planning Sheets   67
Administrator’s Station   16
Agent Help   139,   229
Agent IDs   144
AgentSet   96
Alarm Messages   281
Alarm Priority   47
Alarm Queue   46
Alarms

clearing   45
major   44
minor   42
network   42,   45
system   42

All Messages, Priority Only, and Each New Message Flags   318
All Transient Displays Station Flag   174
Allow Green LEDs   90
Allowed Answer   156

day/night 170
feature code 157

All-Ring Hunt Group   132
Alphanumeric Mode   17
Alternate Hold Timer   211
Alternate Keymap   83, 177
Alternate Menu Displays   80
Alternate Message Source   134,   198
Alternate Transient Display Timer   175
Analog Endpoints

display   81
Off-hook Voice Announce   199
speakerphones   79
volume control   91

Analog Keyset Card (AKSC)   95
Analog Keyset Card (AKSC)/Executone Keyset Card (EKSC)   77
Analog, IDS, and Wave Endpoint Speakerphones   79
ANI   2,   15 3,   15 4
ANI in SMDR   279
Announce Only Calls   220
Announced Transfer   219, 298
Announcement and Overflow Stations   136
Answer Feature Code   157
Answer Supervision   30
Answering Messages   197
ARS-Only Class Of Service 162, 163
ASR   6
Assign Stations to Attendants   18
Assigning the CPC Modem to a DSS/BLF Button   48
Assigning the Modem to a DSS/BLF Button   48
Attendant Console   96

Summary of Contents for Inter-Tel Axxess

































































































































































































































































































































































































Search results

Summary of Contents for Inter-Tel Axxess

Reviews:

Mitel Inter-Tel Axxess, Administrator'S Manual, Page: 371 / 384

Search results

Summary of Contents for Inter-Tel Axxess

Reviews: