manualshive.com logo in svg

Mitel Inter-Tel Axxess, Administrator'S Manual, Page: 136 / 384

Share
Download
Mitel Inter-Tel Axxess Administrator'S Manual Download Page 136

Page  120

System Features

Inter-Tel

® 

Axxess

® 

Administrator Guide — Issue 11.0, May 2008

Station Feature Codes

Display Outside Party Name On/
Off

379

(Display endpoints Only)

 When the endpoint user enters this fea-

ture code, while connected to a CO call that has outside party 
name information, the display will toggle between the caller’s name 
and number. If there is no outside party name or the Expanded CO 
Call Information On Displays flag is disabled, the user will hear a 
burst of reorder tone and see the CANNOT ACCESS FEATURE 
display. If the Display Outside Party Name On/Off feature code is 
programmed in a user programmable button with a lamp, the lamp 
will be lit when the outside party name is enabled and off when the 
outside party number is enabled.

Display Time/Date (ITP)
Show IP Address (SIP)

300

(Display endpoints Only) 

Temporarily displays the system date and 

time, username, and extension number during a call or when other 
displays are shown.

NOTE:  

Feature code 300 displays the IP Address of an endpoint

if it is in SIP mode (see 

page 104

). 

Do-Not-Disturb
Do-Not-Disturb Cancel
Do-Not-Disturb On/Off

370
371
372

The Do-Not-Disturb feature code halts all intercom calls, trans-
ferred calls, and pages to the station. The Cancel code returns the 
station to normal operation. The on/off code can be used to turn 
Do-Not-Disturb on or off. (Inter-Tel endpoints use the DND button.)

Do-Not-Disturb Override

373

(Inter-Tel endpoints only) 

If enabled in the database, allows the 

endpoint user to break through another station’s Do-Not-Disturb 
mode when placing an intercom call

Enhanced Speakerphone Enable

310

(Digital endpoints only) 

When entered at a digital endpoint station, 

this feature code enables the enhanced speakerphone as 
described on 

page 79

. (Digital endpoints can also use the Special 

Speaker buttons.)

Feature Key Default

395

(Inter-Tel endpoints only) 

endpoints have user-programmable fea-

ture buttons that can be set to enter feature codes. This code 
returns the user-programmable buttons to the database default val-
ues.

Group Listen 

312

(Inter-Tel endpoints only) 

Allows a user to transmit a conversation 

over the endpoint speaker while in handset or headset mode

Handsfree On/Off

319

(Inter-Tel endpoints only) 

Disables/enables the endpoint’s hands-

free intercom answering. Incoming intercom calls ring as private 
calls if handsfree answering is disabled.

Headset Enable
Headset Disable
Headset On/Off

315
316
317

(Inter-Tel endpoints only) 

The enable code signals the system that 

a headset has been connected to the endpoint. The disable code 
returns the endpoint to normal operation. The on/off feature code 
can be used to toggle the feature on or off. 

Hold – Individual

336

Places a call on hold so that it can be picked up directly at that sta-
tion or through a reverse transfer from any other station. (Inter-Tel 
endpoints use the HOLD button.)

Table 17. 

Station Feature Codes (Continued)

FEATURE NAME (CONTINUED)

CODE 

DEFINITION (CONTINUED)

Summary of Contents for Inter-Tel Axxess

































































































































































































































































































































































































Reviews:

No comments