manualshive.com logo in svg

Mitel Inter-Tel Axxess, Administrator'S Manual, Page: 288 / 384

Share
Download
Mitel Inter-Tel Axxess Administrator'S Manual Download Page 288

Page  272

System Features

Inter-Tel

® 

Axxess

® 

Administrator Guide — Issue 11.0, May 2008

Remote Forward Programming

Use speed-dial and/or redial numbers (Inter-Tel endpoints only):

 In either numeric

or alphanumeric mode, you can speed dial a number (using the speed-dial button
or feature code). In numeric mode you can press the 

 button to enter the

stored characters. You may chain speed-dial and/or redial numbers together.

6. 

To turn off Do-Not-Disturb: 

Enter the Do-Not-Disturb Off feature code (371). (The

On/Off feature code cannot be used in remote programming.) The call is automatically
disconnected when the feature code is accepted. 

If you entered an invalid feature code,

you will hear reorder tones and can try again. 

REMOTE FORWARD PROGRAMMING

To forward a station using the remote programming feature:

NOTE:  

After each entry, non-display endpoint users will hear a confirmation tone. Outside call-

ers using a DISA line will hear confirmation tone followed by DISA dial tone. Display endpoint
users will not hear confirmation tones but will see a prompt asking for the next entry.

1. 

If calling from an outside endpoint, 

access the system through a DISA line. Enter the

DISA security code (if applicable). You hear a confirmation tone followed by DISA
dial tone.

If programming from another station,

 lift the handset or press the Speaker button.

2. 

Enter the Remote Programming feature code (359). If you have a display, it shows
ENTER EXTENSION. Executive Display, Professional Display, and Model 8560 end-
point users can press the IC DIR button to use the intercom directory to look up a num-
ber.

3. 

Enter the extension to be forwarded. If you have a display, it shows ENTER PASS-
WORD. 

If you entered an invalid extension number,

 you will hear reorder tones and can

try again.

4. 

Enter the extension’s password, followed by 

. If you have a display, it shows ENTER

FEATURE CODE.

NOTE:  

If you enter an incorrect password, 

the display will show INVALID PASS-

WORD, and the call is disconnected. Station users will hear reorder tones.

5. 

To turn on Call Forward: 

 •

Enter one of the following Call Forward feature codes. 

If you entered an invalid

feature code,

 you will hear reorder tones and can try again.

 – 

Call Forward All Calls355

 – 

Call Forward If Busy 357

 – 

Call Forward If No Answer356

 – 

Call Forward If No Answer/Busy358

REDIAL

#

Summary of Contents for Inter-Tel Axxess

































































































































































































































































































































































































Reviews:

No comments