Mitel Inter-Tel Axxess Administrator'S Manual Download Page 378

Page: 378 / 384

Page 362

Index

Inter-Tel

Axxess

Administrator Guide — Issue 11.0, May 2008

On-Hook Monitoring 205
Open Architecture Interface (OAI) 96
Operational Changes 150
Operator Destination

mailbox 316

Optional Account Codes 209
Optional Data Devices   92
Optional DSP Resources   109
Optional Equipment   110

data device   92
data port module   92
headsets   90
MDPM   91
PCDPM   91

Optional System Equipment   109
Options Card (OPC) 109
Outgoing Access   156,   170
Outgoing Access, Allowed-Answer, and Ring-In Assignments   156
Outgoing-Access, Allowed-Answer, and Ring-In Assignments   156
Outside Calls   201

account codes   207
automatic answer   178
callback (queue)   206
camp on   206
header   201
on-hook dialing/monitoring   205
placing   201
receiving   204
remote message notification 319

Outside Party Call Information 154
Outside Party Call Information Has Priority 154
Overflow Stations 136, 1 37

P2P (Peer-to-Peer) 104
Page Zone Keys   83,   84
Pager Notification   317
Paging   124,   264,   265 , 354
Passwords   54

extension ID 294
mailbox 54,   3 15
programming   24
station   269

PC Data Port Module (PCDPM)   91,   1 99
PCDPM   199
Peer-to-Peer (P2P) Audio   104
Peer-to-Peer Audio for IP and SIP Devices   104
Personal Greeting   54
Personal Number   317
Phantom Devices   287
Phone

handsfree enable/disable 184

Pilot Numbers 132
Placing 13

calls on hold   211
conference call   223
entire conference on hold   226
intercom calls   186
nodes in day or night mode 13
outside calls   201

system in night mode 13

Placing a Conference Call 223

Placing Calls On Hold 211

Placing Intercom Calls 186

Placing Nodes in Day or Night Mode 13

Placing Outside Calls 201

Placing the Entire Conference on Hold 226

Placing the System in Night Mode 13

Playback Device 110

announcement station 137

call routing announcement 297

overflow station 137

Polarity Reversal 30

Power Failure Capabilities 284

Power Failure Transfer 110, 284

Power interruption during boot code download 101

Power Supplies 108

Power Supply 75

Premium Features

advanced CO interfaces 30, 153

Primary and Alternate Notification 317

Primary Attendant 129, 13 1

Primary Language 180

Principal Station 232

Private Number

Private Trunk Group 156

Professional Display Endpoint Forward Button 175

Program Station Toll Restrictions 18

Program Usernames 18

Programming

administrator station 16

date and time notification 58

DSS/BLF Buttons 40

private intercom calls 184

station speed-dial numbers and names 246

system speed-dial numbers 38

Programming a DSS/BLF for Agent Wrap-Up 152

Programming and Using DSS/BLF Buttons 40

Programming for Private Intercom Calls 184

Programming Station Speed Dial Numbers and Names 246

Programming System Speed Dial Numbers 38

Programming the Database 16

Programming the Database Using an Administrator’s Station 16

Prompts

alphanumeric 17

date and time 14

Do-Not-Disturb 266

multilingual capability 180

network date and time 15

reminder messages 275

system speed dialing 244

Propagate Original Caller ID on Transfer 154

Summary of Contents for Inter-Tel Axxess

































































































































































































































































































































































































Search results

Summary of Contents for Inter-Tel Axxess

Reviews:

Mitel Inter-Tel Axxess, Administrator'S Manual, Page: 378 / 384

Search results

Summary of Contents for Inter-Tel Axxess

Reviews: