manualshive.com logo in svg

Mitel Inter-Tel Axxess, Administrator'S Manual, Page: 285 / 384

Share
Download
Mitel Inter-Tel Axxess Administrator'S Manual Download Page 285

Page  269

Do-Not-Disturb Override

System Features

Inter-Tel

® 

Axxess

® 

Administrator Guide — Issue 11.0,

 

May 2008

DO-NOT-DISTURB OVERRIDE

If your Inter-Tel endpoint is enabled for Do-Not-Disturb override and you hear Do-Not-Disturb
tones when placing an intercom call, you may use the following procedure to break through
Do-Not-Disturb and complete the call.

Do-Not-Disturb override (Inter-Tel endpoints with this feature enabled only):

When you hear Do-Not-Disturb tones while placing an intercom call, press the Special button
and enter the Do-Not-Disturb Override feature code (373). If the called station is idle, the call
rings as a private intercom call. If the called station is busy, your call camps on.

REMOTE FEATURE PROGRAMMING

The Remote Programming feature allows a user to place an endpoint in Do-Not-Disturb mode
(DND) or forward the station’s calls, or change the password; either from another station or
through DISA. Each station has a password to limit access to this feature. (See 

page 170

 for

information about DISA.)

In a network, Remote Programming can be performed on one node for any Inter-Tel endpoint
that is programmed as an off-node device on that node. You must go through DISA for remote
programming of any endpoints that are not programmed as off-node devices.

STATION PASSWORD

The station password is used only for the Remote Programming feature. 

NOTE:  

To prevent unauthorized use of the call forward feature, 

all

 stations using Remote Pro-

gramming should have a password. To make the passwords difficult to guess, they should not
match the extension number or consist of one digit repeated several times. 

The station password can be up to 8 digits in length. The default password is the extension
number of the station. The password can be changed by entering the Program Station Password
feature code at the station or when using the Remote Programming feature. It can also be pro-
grammed through Individual Station programming.

If the password is changed from a station, the user will be prompted for the old password, then
the new password, and will be asked to verify the new password. If it is programmed through
Remote Programming, the user will already have entered a correct password. In this case, the
user is prompted only for the new password and then asked to verify the password.

Should the verified password and new password not match, the old password will be retained
and the programming session canceled.

Summary of Contents for Inter-Tel Axxess

































































































































































































































































































































































































Reviews:

No comments