manualshive.com logo in svg

Mitel Inter-Tel Axxess, Administrator'S Manual, Page: 278 / 384

Share
Download
Mitel Inter-Tel Axxess Administrator'S Manual Download Page 278

Page  262

System Features

Inter-Tel

® 

Axxess

® 

Administrator Guide — Issue 11.0, May 2008

Using the Last Number Saved Feature

USING THE LAST NUMBER SAVED FEATURE

Use the following procedures to save and redial numbers at stations that are programmed to
use the Last Number 

Saved

 feature.

To save a number on a station programmed for last number saved:

NOTE:  

The saved number is replaced each time you repeat this procedure.

Inter-Tel Endpoints: 

While the endpoint is idle or while listening to intercom dial tone, press

the 

 button, or press the Special button and enter the Redial feature code (380). You

hear a confirmation tone, and the display shows LAST OUTSIDE NUMBER SAVED.

Single-Line Sets: 

Lift the handset and enter the Redial feature code (380). When you hear the

confirmation tone, hang up.

To redial a number (last number saved):

Inter-Tel Endpoints:

 While on a call or after selecting a trunk, press the 

 button, or

press the Special button and enter the Redial feature code (380). Refer to the chart on the pre-
vious page to determine which trunk is selected. The saved telephone number is dialed.

Single-Line Sets:

 While on a call or after selecting a trunk, hookflash/recall and then enter the

Redial feature code (380). Refer to the chart on the previous page to determine which trunk is
selected. The saved telephone number is dialed.

USING THE LAST NUMBER DIALED FEATURE

Use the following procedure to redial numbers at stations that are programmed to use the Last
Number 

Dialed

 feature.

To redial a number (last number dialed):

Inter-Tel Endpoints:

 While on- or off-hook, press the 

 button, or press the Special but-

ton and enter the Redial feature code (380). Refer to the chart on the previous page to deter-
mine which trunk is selected and which digits are dialed.

Single-Line Sets:

 Lift the handset or hookflash/recall. Then enter the Redial feature code

(380). Refer to the chart on the previous page to determine which trunk is selected and which
digits are dialed.

REDIAL

REDIAL

REDIAL

Summary of Contents for Inter-Tel Axxess

































































































































































































































































































































































































Reviews:

No comments