manualshive.com logo in svg

Mitel Inter-Tel Axxess, Administrator'S Manual, Page: 149 / 384

Share
Download
Mitel Inter-Tel Axxess Administrator'S Manual Download Page 149

Page  133

Hunt Group Call Processing

System Features

Inter-Tel

® 

Axxess

® 

Administrator Guide — Issue 11.0,

 

May 2008

HUNT GROUP CALL PROCESSING

Hunt group stations receive the following indications when a call is ringing in:

•

If an outside call is ringing, the station designated to receive the call first shows ring
flash on the associated individual trunk button (if it has one) 

or

 a Call button until the

call is answered or the No Answer Advance timer expires and the call moves to the next
station.

•

If hunt group camp on is allowed and all stations on the hunt group list are unavailable
(busy, in Do-Not-Disturb, or with hunt group remove enabled),

 

an intercom or outside

call will camp on and the stations will receive the following indications:

—

Busy stations 

receive hunt group camp-on tones (if enabled) and display. If there is

an individual trunk button associated with the trunk, it shows ring flash. (There is
a programmable station flag that can disable the camp-on tones for hunt group
calls.)

—

Stations with Hunt Group Remove enabled

 receive camp-on tones and display. If

there is an individual trunk button associated with the trunk, it shows ring flash.

—

Stations with Do-Not-Disturb enabled 

receive no camp on indications, but if there

is an individual trunk button associated with the trunk, it shows ring flash.

—

The first station that becomes available 

receives ringing and a flashing trunk or

Call button. The camp-on and ring flash indications end at the other stations. (The
associated trunk button will be steadily lit at those stations to show that the trunk
is busy.)

•

If hunt group camp on is 

not 

allowed, and all stations on the hunt group list are unavail-

able, the hunt group members will not have any camp-on indications. Callers will hear
one of the following: 

—

Intercom callers

 will hear busy signals.

—

Callers on a trunk not needed to return busy signal 

(such as a T1 E&M) will hear

busy signals.

—

Callers on a trunk needed to return busy signal 

(such as a non-T1 loop-start) will

hear ringing, and the call will be sent to the primary Attendant.

—

ISDN callers

 hear busy signals.

Stations within the hunt group can receive direct trunk ring-in, intercom, forwarded, or trans-
ferred calls to their individual extension numbers without affecting other stations in the hunt
group.

Summary of Contents for Inter-Tel Axxess

































































































































































































































































































































































































Reviews:

No comments