manualshive.com logo in svg

Mitel Inter-Tel Axxess, Administrator'S Manual, Page: 254 / 384

Share
Download
Mitel Inter-Tel Axxess Administrator'S Manual Download Page 254

Page  238

System Features

Inter-Tel

® 

Axxess

® 

Administrator Guide — Issue 11.0, May 2008

Unanswered System Forward Calls

UNANSWERED SYSTEM FORWARD CALLS

If a call that is following a system forwarding path is not answered or all forwarding points are
in Do-Not-Disturb or busy, its final destination depends on the type of call as shown in the
table below.

Table 27. 

Unanswered System Forward Calls 

TYPE OF 

CALL

ALL FWD POINTS ARE 

BUSY OR DO NOT 

ANSWER

ALL FWD POINTS ARE IN DO-NOT-DIS-

TURB

Intercom

Rings at the last forward-
ing point until it is 
answered or the caller 
hangs up. 

Call never leaves the principal station. 

Call routing 
ring-in 
(except DISA)

Rings at last forwarding 
point until it is answered or 
caller hangs up.

Rings at the principal station until it is 
answered or the caller hangs up.

Direct ring-in

Rings at last forwarding 
point until it is answered or 
caller hangs up.

Rings at the principal station until it is 
answered or the caller hangs up.

Transfer from 
a station, 
Automated 
Attendant or 
Voice Mail

Recalls the transferring 
station's transfer recall 
destination when the Sys-
tem Forwarding Advance 
timer expires at the last 
forwarding point.

If immediate forwarding is enabled, 

rings the 

principal station until the applicable Transfer 
timer expires. Then it recalls the transferring 
station's transfer recall destination.

If a conditional forwarding is enabled,

 rings 

principal station until the System Forward Ini-
tiate timer expires. Then it recalls the trans-
ferring station's transfer recall destination.

DISA (includ-
ing Call Rout-
ing to DISA)

Rings at last forwarding 
point until the Abandoned 
Call timer expires.

Rings at the principal station until the Aban-
doned Call timer expires.

Recalls

Recalls the principal sta-
tion's Attendant when the 
System Forwarding 
Advance timer expires at 
the last forwarding point.

If the principal station does 
not have an Attendant, the 
call continues to ring at the 
last forwarding point until 
the Abandoned Call timer 
expires.

If immediate forwarding is enabled, 

rings prin-

cipal station until the Recall timer expires. 
Then it recalls the principal station's Atten-
dant.

If a conditional forwarding is enabled, 

rings 

principal station until the System Forward Ini-
tiate timer expires. Then it recalls the princi-
pal station's Attendant. 

If the principal station does not have an 
Attendant, the call continues to ring at the 
principal station until the Abandoned Call 
timer expires.

Summary of Contents for Inter-Tel Axxess

































































































































































































































































































































































































Reviews:

No comments