manualshive.com logo in svg

Mitel Inter-Tel Axxess, Administrator'S Manual, Page: 124 / 384

Share
Download
Mitel Inter-Tel Axxess Administrator'S Manual Download Page 124

Page  108

System Hardware

Inter-Tel

® 

Axxess

® 

Administrator Guide — Issue 11.0, May 2008

Power Supplies

Model 8602: 

The Model 8602 IP softphone supports most of the features of the Model 8662

hard endpoint, except the following:

•

Automatic Line Access On/Off (fc 360)

•

Automatic Intercom Access On/Off (fc 361)

•

Background Music On/Off (fc 313)

•

Group Listen (fc 312)

•

Handsfree On/Off (319)

•

Headset On, Headset Off, Headset On/Off (fc 315, 316, 317)

•

LCD Contrast Control (fc 303)

•

Ring Tone Selection (fc 398)

•

Switch Keymap (fc 399)

Feature Codes: 

The two feature codes in the table below function differently, depending on

the mode that the endpoint is operating in.

Voice mail displays:

 In SIP mode, voice mail displays are not supported, however, the user

will still receive audio prompts.

Power Supplies

Each SIP and IP device must use a compatible power supply. Because there are so many power
supply options, it is recommended that you refer to the IP Devices Power Supply Matrix
located in the 

IP Devices Installation Manual 

when selecting a power supply for the IP or SIP

device. 

For more information about operating modes and IP devices, see the latest version of the

IP Devices Installation Manual 

(part number 835.2195).

Additional Information and Troubleshooting

For additional information about multi-protocol endpoints not covered in this administrator
guide, see the 

Multi-Protocol Endpoints: Supported Features, Buttons, and LED Indications

document (part number 835.2840). For detailed troubleshooting information, including trou-
bleshooting tables for SIP and IP devices, see the latest version of the 

IP Devices Installation

Manual 

(part number 835.2195).

Table 15: 

Feature Code Exceptions

FEATURE NAME

FEATURE 

CODE

ITP MODE

SIP MODE

Show IP Address
Display Time/Date

300

Displays the system date 
and time, username, and 
extension.

Displays the IP address of 
the endpoint.

Show Version
Diagnostics -Show Version

9928 or 

9128 in Europe

Displays the version and 
date of the call processing 
software.

Displays the firmware ver-
sion on the endpoint.

Summary of Contents for Inter-Tel Axxess

































































































































































































































































































































































































Reviews:

No comments