manualshive.com logo in svg

Mitel Inter-Tel Axxess, Administrator'S Manual, Page: 116 / 384

Share
Download
Mitel Inter-Tel Axxess Administrator'S Manual Download Page 116

Page  100

System Hardware

Inter-Tel

® 

Axxess

® 

Administrator Guide — Issue 11.0, May 2008

Mini-DSS Units

MINI-DSS UNITS

Version 7.0 and later software supports a Mini-DSS that has 16 user-programmable buttons.
This unit attaches directly to either the Model 8520, 8560 or 8660 endpoint and does not
require a PCDPM or AC transformer. Like the DSS/BLF Unit, these buttons contain lamps that
light or flash depending on the status of a station or the button’s programming. For details
about the lamps, see the previous section.

NOTE:  

Version 7.0 or later software is required to use the Mini-DSS.

IP AND SIP DEVICES

IP devices using Inter-Tel Protocol (ITP) and Session Initiation Protocol (SIP) modes allow
users to communicate using the Local Area Network (LAN) and the telephone system. The
telephone system supports the following IP and SIP devices:

•

Hard IP Endpoints

—

Models 8664/8665/8668 (wireless)

—

Model 8660

—

Axxess IP PhonePlus 

—

Eclipse IP PhonePlus

—

IP Single-Line Adapter (IP SLA)

•

Hard Multi-Protocol Endpoints (Operate in ITP or SIP mode)

— Model 8600

— Model 8620

— Model 8622

— Model 8662

— Model 8690

•

Soft IP Endpoints

—

Axxess IP SoftPhone

—

Eclipse IP SoftPhone

—

Model 8602 IP Softphone 

•

Soft SIP Endpoints: Model 8601 SoftPhone for Pocket PC (operates in SIP mode only)

As of V8.1, IP and SIP calls can be routed through the system cabinet or they can be config-
ured as members of the same Network Group. If the devices are routed through the system cab-
inet, they terminate at the 32-Device Internet Protocol Resource Card (IPRC) (see 

page 76

). If

the devices are configured to be members of a Network Group, they can use the peer-to-peer
(P2P) audio feature (see 

page 104

). 

Summary of Contents for Inter-Tel Axxess

































































































































































































































































































































































































Reviews:

No comments