Microsemi SmartFusion2 MSS User Manual Download Page 408 | Manualshive

Page: 408 / 829

background image

Ethernet MAC

UG0331 User Guide Revision 15.0

374

11

Ethernet MAC

The tri-speed (10/100/1000 Mbps) Ethernet medium access controller (TSEMAC) is a medium access
controller which can be configured to 10/100/1000 Mbps data transfer rate (line speed) between the host
processor and Ethernet network. The SmartFusion2 SoC FPGA device has one instance of the TSEMAC
peripheral as part of the microcontroller subsystem (MSS).

11.1

Features

•

Supports tri-speeds: 10/100/1000 Mbps

•

Implements the carrier sense multiple access with the collision detection (CSMA/CD) algorithms
defined by the institute of electrical and electronics engineers (IEEE) 802.3 standard.

•

The advanced high-performance bus (AHB) master port for the direct memory access (DMA)
transfers and AHB-slave port for the configuration space access.

•

The media independent interface (MII), gigabit media independent interface (GMII) and the ten-bit
interface (TBI) for external PHY support.

•

MII/GMII/TBI loopback support

•

4 KB of TX buffer and 8 KB of RX buffer

•

Both TX and RX Buffers are protected by single error correction and dual error detection (SECDED)

•

Standard Ethernet frames of 1522 bytes are supported. Jumbo frames of 9000 bytes are not
supported.

The following figure shows the details of MSS. As shown, TSEMAC can function as an AHB master for
DMA data transfers and as an AHB slave for configuring the TSEMAC from the master
ARM

®

Cortex

®

-M3 processor or from the field programmable gate array (FPGA) fabric logic.

Figure 152 •

MSS Showing a TSEMAC

AHB Bus Matrix

eSRAM_0

System

Controller

Cache

Controller

S

D

IC

ARM Cortex-M3

Processor

S

D

I

MSS DDR

Bridge

PDMA

MS6

MM3

AHB To AHB Bridge with Address Decoder

USB OTG

HPDMA

MDDR

APB_0

SYSREG

Triple Speed
Ethernet MAC

FIC_0

MM4

MS4

MS2

MS3

MS0

MS5

MS1

MM5

MM6

MM7

MM8

MM2

MM1

MM0

MM9

IDC

D/S

eNVM_0

eNVM_1

eSRAM_1

FIC_2 (Peripheral

Initialization)

APB_1

MMUART_0

SPI_0

I2C_0

PDMA

Configuration

WATCHDOG

FIIC

TIMERx2

MMUART_1

SPI_1

I2C_1

GPIO

CAN

RTC

COMM_BLK

FIC_1

MS5_F

IC

MS5_USB

MS5_MAC

MS5_SR

MS5_APB0

MS5_FIC2

MS5_APB1

«
...
406
407
408
409
410
...
»

Summary of Contents for SmartFusion2 MSS






























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartFusion2 MSS

Brand: Rane Pages: 2

Brand: FAAC Pages: 60

Brand: FAAC Pages: 12

Brand: FAAC Pages: 44

Brand: FAAC Pages: 44

Brand: FAAC Pages: 8

Brand: FAAC Pages: 60

Brand: FAAC Pages: 14

Brand: FAAC Pages: 68

Brand: FAAC Pages: 16

Gemini GEM-P9600

Brand: NAPCO Pages: 6

Gemini GEM-P816

Brand: NAPCO Pages: 56

Brand: L-Acoustics Pages: 20

Brand: ZIMMERLI MESSTECHNIK Pages: 12

Brand: H-Tronic Pages: 32

FAREX SR MINI SYSTEM

Brand: RKC INSTRUMENT Pages: 82

Brand: Ros Pages: 10

Brand: Brooks Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands