manualshive.com logo in svg

Microsemi SmartFusion2 MSS, User Manual

Download the free Configuration Manual for Microsemi SmartFusion2 MSS, a cutting-edge product designed for seamless integration and optimized performance. Unlock the full potential of this advanced solution by accessing the comprehensive manual, available for download at our website. Get started now and elevate your technological possibilities with ease.

Share
Download
background image

Universal Serial Bus OTG Controller

UG0331 User Guide Revision 15.0

318

10.3.6.3 CSROL_REG (Host mode) Bit Definitions

5

SendStall

0

The Cortex-M3 processor (or fabric master) writes a 1 to this bit to terminate 
the current transaction. The STALL handshake will be transmitted and then 
this bit will be cleared automatically.

4

SetupEnd

0

This bit is set when a control transaction ends before the DataEnd bit (bit[3] of 
this register) has been set. An interrupt is generated and the FIFO is flushed 
at this time. The bit is cleared by the Cortex-M3 processor (or fabric master) 
writing a 1 to the ServicedSetupEnd bit (bit[7] of this register).

3

DataEnd

0

The Cortex-M3 processor (or fabric master) sets this bit:
– When setting TxPktRdy (bit[1] of this register) for the last data packet.
– When clearing RxPktRdy (bit[0] of this register) after unloading the last data 
packet.
– When setting TxPktRdy (bit[1] of this register) for a zero length data packet.
It is cleared automatically.

2

SentStall

0

This bit is set when a STALL handshake is transmitted. The Cortex-M3 
processor (or fabric master) should clear this bit.

1

TxPktRdy

0

The Cortex-M3 processor (or fabric master) sets this bit after loading a data 
packet into the FIFO. It is cleared automatically when a data packet has been 
transmitted. An interrupt is also generated at this point (if enabled).

0

RxPktRdy

0

This bit is set when a data packet has been received. An interrupt is 
generated when this bit is set. The Cortex-M3 processor (or fabric master) 
clears this bit by setting the ServicedRxPktRdy bit (bit[6]of this register).

Table 214 • 

CSR0L_REG (Host)

Bit 
Number

Name

Reset 
Value

Function

7

NAK Timeout 0

This bit is set when endpoint 0 is halted, following the receipt of NAK responses 
for longer than the time set by the NAKLimit0 register. The Cortex-M3 processor 
(or fabric master) should clear this bit to allow the endpoint to continue.

6

StatusPkt

0

The Cortex-M3 processor (or fabric master) sets this bit at the same time as the 
TxPktRdy (bit[1] of this register) or ReqPkt bit (bit 0 of this register) is set, to 
perform a status stage transaction. Setting this bit ensures that the data toggle is 
set to 1 so that a DATA1 packet is used for the status stage transaction.

5

ReqPkt

0

The Cortex-M3 processor (or fabric master) sets this bit to request an IN 
transaction. It is cleared when RxPktRdy (bit [0] of this register) is set.

4

Error

0

This bit will be set when three attempts have been made to perform a transaction 
with no response from the peripheral. The Cortex-M3 processor (or fabric master) 
should clear this bit. An interrupt is generated when this bit is set.

3

SetupPkt

0

The Cortex-M3 processor (or fabric master) sets this bit, at the same time as the 
TxPktRdy bit (bit[1] of this register) is set, to send a SETUP token instead of an 
OUT token for the transaction.
Setting this bit also clears the Data Toggle.

2

RxStall

0

This bit is set when a STALL handshake is received. The Cortex-M3 processor (or 
fabric master) should clear this bit.

Table 213 • 

CSR0L_REG (Peripheral)

 (continued)

Bit 
Number Name

Reset 
Value Function

Summary of Contents for SmartFusion2 MSS






























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartFusion2 MSS

GBD SC Series Electrical Connections preview
SC Series
Brand: GBD Pages: 12
Gantner E Series Communications Manual preview
E Series
Brand: Gantner Pages: 56
GBD BA100 Instructions For Installations preview
BA100
Brand: GBD Pages: 68
Calsense ET2000e Programming Manual preview
ET2000e
Brand: Calsense Pages: 74
Jedo Trim User Manual preview
Trim
Brand: Jedo Pages: 26
Neets echo plus User Manual preview
echo plus
Brand: Neets Pages: 12
National Instruments NI 9871 Operating Instructions And Specifications preview
NI 9871
Brand: National Instruments Pages: 24
Samwontech TEMP2000 Series Installation Manual preview
TEMP2000 Series
Brand: Samwontech Pages: 91
Warren rupp HDF3-A Original Instructions Manual preview
HDF3-A
Brand: Warren rupp Pages: 18
Yamaha QL5 Manual preview
QL5
Brand: Yamaha Pages: 100
Peg-Perego Porte-enfant Instructions For Use Manual preview
Porte-enfant
Brand: Peg-Perego Pages: 68
ETNA Hydropan-Single Operation And Maintenance Manual preview
Hydropan-Single
Brand: ETNA Pages: 12
Z-Wave Z-URC 550EU Operating Instructions Manual preview
Z-URC 550EU
Brand: Z-Wave Pages: 44
Powers HydroGuard 1430 Series Quick Start Manual preview
HydroGuard 1430 Series
Brand: Powers Pages: 8
HTW HTW-RG66 Owner'S Manual preview
HTW-RG66
Brand: HTW Pages: 88
Powtran PR5200 011G3 User Manual preview
PR5200 011G3
Brand: Powtran Pages: 40
Radio Shack Wireless Security Keychain Remote Owner'S Manual preview
Wireless Security Keychain Remote
Brand: Radio Shack Pages: 2
Curtis 1232E Manual preview
1232E
Brand: Curtis Pages: 30

Brands by name

Popular brands

Load more brands