manualshive.com logo in svg

Microsemi SmartFusion2 MSS, User Manual

Download the free Configuration Manual for Microsemi SmartFusion2 MSS, a cutting-edge product designed for seamless integration and optimized performance. Unlock the full potential of this advanced solution by accessing the comprehensive manual, available for download at our website. Get started now and elevate your technological possibilities with ease.

Share
Download
background image

Fabric Interface Controller

UG0331 User Guide Revision 15.0

769

FIC_0_CLK, and FIC_1_CLK must be set to 1:1 when bypass mode is selected. This requirement is 
enforced in the MSS CCC Configurator when bypass is selected.

Figure 340 • 

Advanced Options Configuration

Expose Master Identity Port

: Use this option to expose a 2-bit side band signal to the FPGA fabric (one 

2-bit signal per FIC instance). This option is only active if you selected the interface to act as a master of 
the fabric.

24.7.1.1.3 FPGA Fabric Address Regions (MSS Master View)

Up to six different memory regions can be assigned to each FIC in the MSS memory map. By default, 
fabric regions 0, 1, and 2 are accessible through FIC_0, and regions 3, 4, and 5 are accessible through 
FIC_1 as shown in the following figure.

Figure 341 • 

FPGA Fabric Address Regions (MSS Master View)

Note:

This option is available in FIC_0 configurator only. If memory regions are required to be configured to 
FIC_1, the FIC_0 configurator needs to be opened.

24.7.1.2 Step 2: Create the FPGA Fabric FIC Subsystem

For each FIC interface—master and slave—exposed, a bus (CoreAHBLite or CoreAPB3) must be 
instantiated that matches the type selected. Depending on the interface role (master/slave) and type 
(AHB-Lite/APB), the bus configuration is described in the following sections.

24.7.1.2.1 Master/AHB-Lite

Instantiate and configure the CoreAHBLite bus as follows:

1.

Select the 

Memory Space

 option that matches requirements:

•

If less than 16 MB of address space is required for all peripherals, select the option as shown in 
the following figure. This mode provides sixteen, 16 MB slots that can be used to connect up to 
sixteen AHB-Lite slaves.

Figure 342 • 

Master/AHB-Lite Memory Space Configuration – 16 MB per Slot

Summary of Contents for SmartFusion2 MSS






























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartFusion2 MSS

Parker 890 Series Quick Start Manual preview
890 Series
Brand: Parker Pages: 30
VAT 110 Series Installation, Operating, & Maintenance Instructions preview
110 Series
Brand: VAT Pages: 22
Yudian AI Series Operation Instruction Manual preview
AI Series
Brand: Yudian Pages: 26
Harman AMX JPK-1300 Quick Start Manual preview
AMX JPK-1300
Brand: Harman Pages: 2
T-Link TL300 Quick Install Manual preview
TL300
Brand: T-Link Pages: 3
ZIGBEE RC-02 User Manual preview
RC-02
Brand: ZIGBEE Pages: 5
LAE electronic LF28 Instructions For Installation And Use Manual preview
LF28
Brand: LAE electronic Pages: 7
LAE electronic AT1-5 Instructions For Use preview
AT1-5
Brand: LAE electronic Pages: 2
Parker AC890PX Series User Mounting And Assembly Instructions preview
AC890PX Series
Brand: Parker Pages: 30
Parker Compax3M Series Installation Manual preview
Compax3M Series
Brand: Parker Pages: 52
Parker AC30V Series Manual preview
AC30V Series
Brand: Parker Pages: 337
S&P RMB Quick Start Manual preview
RMB
Brand: S&P Pages: 17
S&S Northern Merlin 1000VW+ Installation, Operating And Maintenance preview
Merlin 1000VW+
Brand: S&S Northern Pages: 9
WAREMA Wisotronic Operating Instructions Manual preview
Wisotronic
Brand: WAREMA Pages: 112
WAGO 750-880 Manual preview
750-880
Brand: WAGO Pages: 414
V2 Blitz Manual preview
Blitz
Brand: V2 Pages: 48
Yngri YORK Manual preview
YORK
Brand: Yngri Pages: 20
Eaton Cutler-Hammer LMR Instructions Manual preview
Cutler-Hammer LMR
Brand: Eaton Pages: 38

Brands by name

Popular brands

Load more brands