manualshive.com logo in svg

Microsemi SmartFusion2 MSS, User Manual

Download the free Configuration Manual for Microsemi SmartFusion2 MSS, a cutting-edge product designed for seamless integration and optimized performance. Unlock the full potential of this advanced solution by accessing the comprehensive manual, available for download at our website. Get started now and elevate your technological possibilities with ease.

Share
Download
background image

CAN Controller

UG0331 User Guide Revision 15.0

460

12.6.7

Receive Message Control and Command Register

Each receive buffer can be configured through a set of registers. Those registers are broken down into a 
Command/Control register, Identifier register, Data high register, and Data low register, Acceptance mask 
register (AMR), Acceptance code register (ACR), AMR data, and ACR data. The following tables provide 
a detailed description of receive message0 buffer registers bits.       

Table 450 • 

RX_MSG0_CTRL_CMD

Bit Number

Name

Reset Value

Description

[31:24]

Reserved

0

Reserved

23

WPNH

1

Write protect not high
0: Bit[21:16] remain unchanged
1: The write protect is not set and bit[21:16] are modified, 
default
The read back value of this bit is undefined

22

Reserved

0

Reserved

21

RTR

0

RTR bit; Control bit
0: This is a regular message
1: This is an RTR message.

20

IDE

0

Extended identifier bit; Control bit
0: This is a standard format message.
1: This is an extended format message.

[19:16]

DLC

0

Data length code; Control bits
0: Message has 0 data byte.
1: Message has 1 data byte.
...
8: Message has 8 data bytes.
9-15: Message has 8 data bytes.

[15:8]

Reserved

0

Reserved

7

WPNL

1

Write protect not low
0: Bits[6:3] remain unchanged
1: This write protect is not set and bits[6:3] are modified, 
default.
This bit is always zero for read back

6

LF

0

Link flag; Control bit
0: This buffer is not linked to the next
 buffer
1: This buffer is linked with the next buffer

5

RxIntEbl

0

Receive interrupt enable; Control bit
0: Interrupt generation is disabled
1: Interrupt generation is enabled

4

RTRreply

0

Automatic message reply upon receipt of an RTR 
message; Control bit
0: Automatic RTR message handling disabled
1: Automatic RTR message handling enabled

3

TxBufferEbl

0

Transaction buffer enable; Control bit
0: Buffer is disabled
1: Buffer is enabled

Summary of Contents for SmartFusion2 MSS






























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartFusion2 MSS

GE NetworX NX-6V2 Installation Instructions Manual preview
NetworX NX-6V2
Brand: GE Pages: 8
KEENZ Class Instruction Manual preview
Class
Brand: KEENZ Pages: 24
Baby Jogger VUE Assembly Instructions Manual preview
VUE
Brand: Baby Jogger Pages: 24
Baby Jogger POD Assembly Instructions Manual preview
POD
Brand: Baby Jogger Pages: 16
Baby Jogger city select LUX Assembly Instructions Manual preview
city select LUX
Brand: Baby Jogger Pages: 20
Baby Jogger CITY ELITE SINGLE Instructions For Use Manual preview
CITY ELITE SINGLE
Brand: Baby Jogger Pages: 24
Baby Jogger CITY MINI 2 Assembly Instructions Manual preview
CITY MINI 2
Brand: Baby Jogger Pages: 147
BADODOSECURITY G200 Quick Manual preview
G200
Brand: BADODOSECURITY Pages: 8
Eaton CF2000 Installation And Operation Manual preview
CF2000
Brand: Eaton Pages: 100
Racal Instruments 1260 Manual preview
1260
Brand: Racal Instruments Pages: 94
Racal Instruments 1260 User Manual preview
1260
Brand: Racal Instruments Pages: 97
Omega PHCN-37 User Manual preview
PHCN-37
Brand: Omega Pages: 56
Omega DP25-TC Quick Start Manuals preview
DP25-TC
Brand: Omega Pages: 2
xpr VPROX2-M User Manual preview
VPROX2-M
Brand: xpr Pages: 4
Radionics D9000 Series Installation And Troubleshooting Quick Reference preview
D9000 Series
Brand: Radionics Pages: 14
Sherlotronics FPP2 Installation Manual preview
FPP2
Brand: Sherlotronics Pages: 2
Jeckson Electric 47-1010A-T Owner'S Manual preview
47-1010A-T
Brand: Jeckson Electric Pages: 2
Znshine Solar ZXM6-72M Mounting Manual preview
ZXM6-72M
Brand: Znshine Solar Pages: 16

Brands by name

Popular brands

Load more brands