manualshive.com logo in svg

Microsemi SmartFusion2 MSS, User Manual

Download the free Configuration Manual for Microsemi SmartFusion2 MSS, a cutting-edge product designed for seamless integration and optimized performance. Unlock the full potential of this advanced solution by accessing the comprehensive manual, available for download at our website. Get started now and elevate your technological possibilities with ease.

Share
Download
background image

Cortex-M3 Processor (Reference Material)

UG0331 User Guide Revision 15.0

96

If a pending interrupt is enabled, the NVIC activates the interrupt based on its priority. If an interrupt is not 
enabled, asserting its interrupt signal changes the interrupt state to pending, but the NVIC never 
activates the interrupt, regardless of its priority.

3.7.1.4

Interrupt Clear-enable Registers

The NVIC_ICER0-NVIC_ICER7 registers disable interrupts, and show which interrupts are enabled. See 
the register summary in 

Table 40, 

page 95 for the register attributes.

The bit assignments are: 

Figure 24 • 

ICER Register Bit Assignments

3.7.1.5

Interrupt Set-pending Registers

The NVIC_ISPR0-NVIC_ISPR7 registers force interrupts into the pending state, and show which 
interrupts are pending. See the register summary in 

Table 40, 

page 95 for the register attributes.

The bit assignments are:

Figure 25 • 

ISPR Register Bit Assignments

Table 42 • 

NVIC_ISER Bit Assignments

Bits

Name

Function

[31:0]

SETENA

Interrupt set-enable bits. 
Write:
0: no effect
1: enable interrupt.
Read:
0: interrupt disabled
1: interrupt enabled.

Table 43 • 

NVIC_ICER Bit Assignments

Bits

Name

Function

[31:0]

CLRENA

Interrupt clear-enable bits.
Write:
0: no effect
1: disable interrupt.
Read:
0: interrupt disabled
1: interrupt enabled.

CLRENA bits

31

0

SETPEND bits

31

0

Summary of Contents for SmartFusion2 MSS






























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartFusion2 MSS

Canon imageRUNNER ADVANCE C9075S PRO User Manual preview
imageRUNNER ADVANCE C9075S PRO
Brand: Canon Pages: 20
Gardena 4030 Operator'S Manual preview
4030
Brand: Gardena Pages: 16
MADRIX STELLA Technical Manual & Quick Start Manual preview
STELLA
Brand: MADRIX Pages: 28
Balmar Max Charge MC-624 Installation And Operator'S Manual preview
Max Charge MC-624
Brand: Balmar Pages: 8
Balmar MAX CHARGE MC-614 Installation And Operation Manual preview
MAX CHARGE MC-614
Brand: Balmar Pages: 20
babyzen YOYO User Manual preview
YOYO
Brand: babyzen Pages: 11
Kathrein CAP Converter Operating Instructions Manual preview
CAP Converter
Brand: Kathrein Pages: 16
Wang 2236 Product/Maintenance Manual preview
2236
Brand: Wang Pages: 68
NAVITAS TSE Series Installation Manual preview
TSE Series
Brand: NAVITAS Pages: 14
Maximum Controls MAX ARM Installation And Owner'S Manual preview
MAX ARM
Brand: Maximum Controls Pages: 58
Allen-Bradley 1756-L72EROM Installation Instructions Manual preview
1756-L72EROM
Brand: Allen-Bradley Pages: 16
D+H RCM 230-11-U Original Instructions preview
RCM 230-11-U
Brand: D+H Pages: 2
Yolink YS4803-UC User Manual preview
YS4803-UC
Brand: Yolink Pages: 23
Rabbit microBLUE Instruction Manual preview
microBLUE
Brand: Rabbit Pages: 12
ICP DAS USA ECAT-2061 Quick Start preview
ECAT-2061
Brand: ICP DAS USA Pages: 4
ProSoft Technology InRAX MVI46-PDPS Manual preview
InRAX MVI46-PDPS
Brand: ProSoft Technology Pages: 72
Chamberlain 972LM Security? Owner'S Manual preview
972LM Security?
Brand: Chamberlain Pages: 4
VAT 613 Series Installation, Operating, & Maintenance Instructions preview
613 Series
Brand: VAT Pages: 149

Brands by name

Popular brands

Load more brands