MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 71

Page: 71 / 324

2-53

BEFORE DRIVING

68PH0-74E

Speedometer

The speedometer indicates vehicle speed.

Fuel Gauge

68PH02202

When the ignition switch is in the “ON”

position, this gauge gives an approximate

indication of the amount of fuel in the fuel

tank. “F” stands for full and “E” stands for

empty.
If the fuel meter indicator shows only one

segment to “E”, refill the tank as soon as

possible.

NOTE:

If the last segment blinks, it means that the

fuel is almost empty.

If the low fuel warning light (1) comes on,

fill the fuel tank immediately.

NOTE:

The activation point of the low fuel warning

light (1) varies depending on road condi-

tions (for example, slope or curve) and

driving conditions because of fuel moving

in the tank.

Refer to “Low Fuel Warning Light” in

“Warning and Indicator Lights” in this sec-

tion for details.
The mark (2) indicates that the fuel filler

door is located on the left side of the vehi-

cle.

(1)

(2)

(1)

(2)

EXAMPLE

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands