MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 258

Page: 258 / 324

7-2

INSPECTION AND MAINTENANCE

68PH0-74E

Maintenance Schedule

The following table shows the times when

you should perform regular maintenance

on your vehicle. This table shows in kilo-

meters and months when you should per-

form inspections, adjustments, lubrication

and other services.

Periodic Maintenance
Schedule

“C”: Clean

“R”: Replace or Change

“I”: Inspect, clean, adjust, lubricate or

replace as necessary

“L”: Lubricate

“T”: Tighten to Specified Torque

“O”: Rotate

NOTE:

This table includes services as scheduled

up to 80,000 km mileage. Beyond 80,000

km, carry out the same services at the

same intervals respectively.

WARNING

MARUTI SUZUKI recommends that

maintenance on your Maruti Suzuki

vehicle should be performed by MAR-

UTI SUZUKI authorized workshop/

Service station.

NOTICE

Whenever it becomes necessary to

replace parts on your vehicle, it is

recommended that you use MARUTI

genuine replacement parts or their

equivalent.

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands