MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 154

Page: 154 / 324

3-24

OPERATING YOUR VEHICLE

68PH0-74E

• Turn the ignition switch to the “ON” position or press the engine switch to change the

ignition mode to “ON” with the parking sensor switch in the “ON” position.

• Push the switch again and it stays in; this is the OFF position. The indicator in the

switch goes out and the parking sensor is deactivated.

NOTE:

• If you push the parking sensor switch from the “OFF” to “ON” position when the ignition

switch is turned to “ON” position or the engine switch is pressed to change the ignition

mode to “ON”, the inside buzzer sounds.

• When the gearshift lever is shifted to the “R” (Reverse) position with the system ON, a

buzzer will sound once.

Switch position

State

EXAMPLE

• When the indicator light is on and all necessary conditions are

met, system becomes ready for operation.

EXAMPLE

OFF

• The system does not operate. Push the switch to turn off the

indicator if you do not wish to use the parking sensor.

Obstacle Indication by Parking Sen-

sor

Information display symbol

(If equipped)

68PH02302

(1) Obstacle detected by rear center sensors

(2) Obstacle detected by rear corner sensors

Upon detecting an obstacle, the parking

sensor causes an interior buzzer to sound

and a symbol representing the obstacle

appears on the information display in the

instrument cluster (If equipped).

• A different symbol is displayed depend-

ing on the direction and distance of the

obstacle. (If equipped)

• A buzzer located behind the rear seat

sounds when a sensor at the rear

detects an obstacle.

(1)

(2)

(1)

(2)

EXAMPLE

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands