MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 59

Page: 59 / 324

2-41

BEFORE DRIVING

68PH0-74E

Some child restraint systems require the

use of a top tether strap. Top tether anchor-

age brackets are provided in your vehicle at

the locations shown in the illustrations.

The number of the top tether anchorage

brackets provided in your vehicle depends

on the vehicle specification. Install the child

restraint system as follows:
1) Remove the luggage compartment cover

(If equipped).

2) Secure the child restraint on the rear

seat using the procedure described

above for securing a restraint system

that does not require a top tether strap.

3) Hook the top tether strap to the top

tether anchorage bracket and tighten

the top tether strap according to the

instructions provided by the child

restraint system manufacturer. Attach

the top tether strap to the correspond-

ing top tether anchorage bracket

located directly behind the child

restraint. Do not attach the top tether

strap to the luggage restraint loops (If

equipped).

54P000264

4) When routing the top tether strap, pass

the top tether strap as shown in the

illustration. (Refer to “Head restraints”

section for details on how to remove the

head restraint.)

5) Check that cargo does not interfere

with routing of the top tether strap.

NOTE:

Maruti Suzuki recommends use of Maruti

Suzuki Genuine accessory of “Child seat,

ISOFIX”.

WARNING

Do not attach the child restraint top

tether strap to the luggage restraint

loops (If equipped). Incorrectly

attached top tether strap will reduce

the intended effectiveness of the

child restraint system.

NOTICE

When installing a child restraint sys-

tem to the rear seat, adjust the front

seat position so that the front seat

does not interfere with the child

restraint system.

EXAMPLE

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands