MARUTI SUZUKI BALENO 2017 Owner'S Manual Download Page 173

Page: 173 / 324

5-1

OTHER CONTROLS AND EQUIPMENT

68PH0-74E

Fuel Filler Cap

68PM05001

68PH00574

The fuel filler cap is located on the left rear

side of the vehicle. The fuel filler door can

be unlocked by pulling up the opener lever

located on the outboard side of the driver’s

seat and locked by simply closing the door.

57L51093

To remove the fuel filler cap:

1) Open the fuel filler door.

2) Remove the cap by turning it counter-

clockwise.

68PH00502

NOTE:

The cap holder (1) holds the fuel filler cap

(2) by hooking the groove (3) when refuel-

ing.

To reinstall the fuel filler cap:

1) Turn the cap clockwise until you hear

several clicks.

2) Close the fuel filler door.

EXAMPLE

CAUTION

Remove the fuel filler cap slowly. The

fuel may be under pressure and may

spray out, causing injury.

Open

EXAMPLE

WARNING

Fuel is extremely flammable. Do not

smoke when refueling, and make

sure there are no open flames or

sparks in the area.

(1)

(2)

(3)

(1)

EXAMPLE

Summary of Contents for BALENO 2017





































































































































































































































































































































Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands

MARUTI SUZUKI BALENO 2017, Owner'S Manual

Search results

Summary of Contents for BALENO 2017

Reviews:

Related manuals for BALENO 2017

Brands by name

Popular brands